Hafler SR2800CE, SR2300CE Wiring Diagrams, Stereo Mode SR2300/SR2800, Biamp Mode SR2300/SR2800

Wiring Diagrams

STEREO MODE (SR2300/SR2800)

Load Power

100V 70V

8Ω 4Ω 2Ω

100V 70V

8Ω 4Ω 2Ω

				– 3		—
				–	+
				+		300W
			1	2		2Ω – 8Ω
				Audio GND
				Chassis Float
CH A	BIAMP STEREO	CH A			—	+
IN		OUT		600W
				4Ω– 16Ω	+
				Mono,70V,100V		+
			For 70V, 100V, or Mono
			• Use CH B input
			• Load across RED
			terminals
			• Set load switches to one			300W
CH B		CH B	half load impedance
						2Ω – 8Ω
IN	(Mono)	OUT				—

S R 2 3 0 0

300 W Stereo, 2Ω – 8Ω

600W Mono, 70V,100V

Attention: Utiliser un fusible de rechange de même type.

CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.

250W 250V T7A 100V-120V~

50-60Hz

CE SPEAKON

Connector

Wiring

A Division of

Rockford Corp.

Tempe, AZ 85281

Made in the U.S.A.

1.Connect signal from source to both CH A and CH B inputs.

2.Move Biamp/Stereo switch to Stereo input mode.

3.Move Stereo/Mono switch to Stereo mode.

4.Select desired speaker load (8Ω/4Ω/2Ω) for each channel – CH A & CH B loads do not need to match.

BIAMP MODE (SR2300/SR2800)

5.Connect appropriate speaker load 8Ω/4Ω/2Ω to 5-way binding posts. CE units: Connect as shown above for Dual SPEAKONs or Single 4-Wire SPEAKON.

6.Adjust CH A & CH B level controls independently.

Load Power

100V 70V

8Ω 4Ω 2Ω

100V 70V

8Ω 4Ω 2Ω

				– 3		—
				–	+
				+		300W
			1	2		2Ω – 8Ω
				Audio GND
				Chassis Float
CH A	BIAMP STEREO	CH A			—	+
IN		OUT		600W
				4Ω– 16Ω	+
				Mono,70V,100V		+
			For 70V, 100V, or Mono
			• Use CH B input
			• Load across RED
			terminals
			• Set load switches to one			300W
CH B		CH B	half load impedance
						2Ω – 8Ω
IN	(Mono)	OUT				—

S R 2 3 0 0

300 W Stereo, 2Ω – 8Ω

600W Mono, 70V,100V

Attention: Utiliser un fusible de rechange de même type.

CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.

250W 250V T7A 100V-120V~

50-60Hz

CE SPEAKON

Connector

Wiring

A Division of

Rockford Corp.

Tempe, AZ 85281

Made in the U.S.A.

1.Connect signal from source to CH B input.

2.Move Biamp/Stereo switch to BIAMP input mode.

3.Move Stereo/Mono switch to Stereo mode.

4.Select desired speaker load (8Ω/4Ω/2Ω) for each channel — CH A and CH B loads do not need to match.

5.Connect appropriate speaker load 8Ω/4Ω/2Ω to 5-way binding posts. CE units: Connect as shown above for Dual SPEAKONs or Single 4-Wire SPEAKON.

6.Adjust CH A & CH B level controls independently.

– 18 –