S a l t 
Salt
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimise and customise the level of salt consumption so that it remains at a minimum.
To adjust salt consumption, proceed as follows:
Detergent and Rinse Aid
Detergent
Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle Table" .The detergent dispenser is located on the inside panel the door.
Rinse Aid
This product makes dishes sparkle and helps them to dry with- out spotting. The dispenser is located on the inside panel of the door and should be filled after every 80 wash cycle (or when the rinse aid indicator light comes on for models with this feature).
Loading the Rinse Aid
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should be filled as follows:
-Remove the lower rack and then unscrew and remove the cap from the salt container;
-If you are filling the container for the first time, fill it with water;
-Place the end of the funnel (supplied) into the hole and intro- duce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container.
-Carefully screw the cap back on.
- Unscrew the cap from the salt container;
- There is a ring on the container with an arrow on it (see figure). - If necessary, rotate the ring in the anticlockwise direction from the
the water being used.
It is recommended that adjustments be made in accordance with the following scheme:
Loading the detergent
To open the "A" cover on the dispenser, press the "B" button. The detergent for the wash cycle should be poured into the "C" compartment.
After the detergent has been placed in the dispenser, close the cover and press down until it clicks in place.
C
A
B
NOTE: To facilitate closing the cover, remove any excess de-
tergent on the edges of the dispenser.
To open the dispenser, turn the "C" cap in an
Important
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs, the dosage adjuster should be turned to a higher setting.
If the dishes have white streaks, turn the dosage adjuster to a lower setting.
C
F
C
The salt container must be filled when the "low salt" indicator light appears on the control panel.
To prevent the formation of rust, load the salt just before begin- ning a wash cycle.
| Water Hardness |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Selector | Salt | Autonomy |
| Level | Clarke | º dH |
| c o n s u m p t i o n | |||
| mmol/l | (cycles/2kg) | ||||||
|
| degrees |
|
| position | (Grams/cycle) |
| |
|
|
|
|
|
|
|
|
|
1 | 0 | 14 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
3 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
4 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
.3. | GB | .4. |
GB |
|
