Operation
Universal Remote Control
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in six different modes: TV, DVD, VCR, SETBOX , CABLE or AUDIO.
Note
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
Control Operation
1.Program the Controller to work with your device. 2.Changing device mode by pressing the TV 
DVD 
STB 
CABLE 
VCR 
AUD key. When device is set, related device LED will be on for 1 second and then be off.
3.Aim the remote at the device.
4.Use the other Controller buttons to operate the device. Device LED will blink if user presses any key (if the key has data in current mode.). If the key has no data, then LED will not blink.
5.Default init status: TV/Haier codeset.
Manually Programming the Control
Check the code no. from the code list.
1.Choose the device you want to program.
2.While Press and holding ENTER key, press INPUT key, and device LED will be ON. Keep the status for about 3 seconds and the LED will blink, indicating that the Controller is ready for programming, then
release both keys.
3.Led will blink once when you enter a digit key, indicating the digit key is programmed. If 3 digits are programmed successfully, device LED will be ON for about 3 seconds and then blink twice per second. Then User now can:
a)Try to operate the device by using power key.
B)If operation can be done, press ENTER key to save current
C)Return to beginning of step 3. Reprogram the control.
4.If user's input is incorrect, LED will blink 6 times in 3 seconds (2HZ). And then keep 2HZ blink, user now can return to step 3 and
Within 30 seconds, user should enter the
Manually scan mode
With manually scan programming, the Controller tests all the codes available in the codeset database and assign the correct one for the selected device. Although this method is more time consuming, it saves you the trouble of looking up the brand codes necessary for manual programming.
To
1.Manually turn OFF the device for manually scan mode. (TV, VCR, DVD, STB, cable box or audio equipment).
2.Choose the device you want to program.
3.While Press and holding ENTER key, press INPUT key, and device LED will be ON. Keep the status for about 3 seconds and the LED will blink, indicating that the Control is ready for programming, then release both keys.
4.Press and release the CH+/CH- key. it will emit the next or the previous POWER key code. The LED blinks with 10HZ freq, indicating that the Remote is in manually scan mode.
5.Press CH+/CH- key repeatedly until the device switches ON(CH+ key conducts a upward search while the CH- key conducts a downward search in the code set database). When the device turns ON, press and release the ENTER key to program the Controller with the new code, saving the code to EEPROM and exit.
6.After saving the new code, press POWER key. If the device responds, no further programming is required.
If the device does not respond, repeat step 3 through 5. And searching will start from current code set.
To exit without programming, press any key or no key was pressed in 30 second, manually scan mode will be automatically exit. The code can not be saved to
EEPROM.
After searching the entire data base, this mode will be automatically exited and led will blink for 3 times in 1.5 seconds. The code can not be saved to EEPROM.
Automatic Scan Programming the Controller To automatic scan program the Controller:
1.Manually turn OFF the device you wish to power scan. (TV, VCR, DVD,STB, cable box or audio equipment).
2.choose the device you wish to program.
3.While Press and holding ENTER key, press the INPUT key and device LED will be ON. Keep the status for about 3 seconds and the LED will blink, indicating that the Controller is ready for programming, then release
both keys.
4.Press and release the Mute key to enter automatic scan mode. And the remote will automatically sending codes to the device per 2 seconds.
5.When the device turns ON, press ENTER key to program the Controller with the new code, saving it to EEPROM and exit.
6.Press POWER key, If the device responds, no further programming is required. If the device does not respond repeat steps 1 through 5.
7.After searching the entire data base, this mode will be automatically exited and led will blink for 3 times. The codeset is not saved to EEPROM.
In automatic scan mode, press any key other than ENTER key will exit without programming,.
34 TV
