![](/images/new-backgrounds/1214038/21403813x1.webp)
2.NOTE: When mounting the Micro Mill/Drill Machine on a workbench, you will need four 3/8” diameter bolts of appropriate length, four lock washers, and four nuts (not provided).
LIFTING HAND WHEEL | LIFTING HAND WHEEL |
(#97) | (#97) |
SPINDLE |
|
|
|
|
|
|
|
|
|
|
|
| |
BOX |
|
|
|
|
|
|
|
|
| HANDLE | |||
(#24) |
|
|
| HIGH/LOW SPEED KNOB |
|
|
| ||||||
|
|
|
|
|
| SHAFT | |||||||
|
|
|
|
|
|
| |||||||
|
| (#124) |
|
|
|
|
| ||||||
|
|
|
| (#87) | |||||||||
|
|
|
|
| CLUTCH LEVER | ||||||||
|
|
|
|
|
|
|
|
|
|
| |||
FORWARD |
|
| CLUTCH | (#65) |
|
|
|
|
|
|
| ||
|
| LEVER (#65) |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||
OFF |
|
|
|
|
|
|
|
|
|
| |||
|
|
| FINE FEEDING |
|
|
|
|
| SPINDLE | ||||
REVERSE |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| BOX | |||
SWITCH |
|
| HAND WHEEL (#97) |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||||
|
|
|
| (#24) | |||||||||
(#125) |
|
|
|
|
| FINE FEEDING | |||||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| HAND WHEEL |
|
|
|
|
|
| |
|
|
|
|
| HANDLE SHAFT | (#97) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
VARIABLE | (#87) |
|
|
|
|
|
|
|
| ||||
SPEED |
|
|
| CHUCK (#132) |
|
|
|
|
|
|
|
| |
KNOB (#122) |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| CHUCK | ||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| (#132) | ||||
WORK |
|
|
| LONGITUDINAL FEED |
| ||||||||
|
|
|
|
|
|
|
|
| |||||
|
|
| HAND WHEEL |
|
|
|
|
|
| ||||
TABLE |
| (#97) |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||||
(#105) |
|
|
|
|
|
|
|
|
|
|
| WORK | |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| TABLE | |
|
|
|
|
|
|
|
|
| (#105) | ||||
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CROSS FEED | LONGITUDINAL FEED |
HAND WHEEL (#97) | HAND WHEEL (#97) |
FIGURE B
3.With assistance, position the Micro Mill/Drill Machine in the desired location on the top of the workbench. Use the four mounting holes in the Base (part #74) of the Micro Mill/Drill Machine as a template, and trace with a pencil on the top of the workbench four 3/8” diameter mounting holes . Then, temporarily remove the Micro Mill/Drill Machine from the workbench. (See Assy. Diagram.)
4.Where the four pencil marks are located, drill four 3/8” diameter holes completely through the top of the workbench.
SKU 47158 | For technical questions, please call | Page |