FRONT-PANEL CONTROLS
| 29 | ı |
| Û | Ò | Ô |
|
30 |
| ˆ Ù |
|
| Ú | |
|
| AVR 125 |
|
|
|
|
|
|
|
|
|
| dB |
|
|
|
|
|
|
|
|
|
| Ó |
|
|
|
|
|
|
| ( |
|
|
|
| AM/FM |
|
| * |
1 |
|
|
|
|
|
| |
|
|
|
|
|
| & | |
|
|
|
|
|
|
| |
2 |
|
|
|
|
|
|
|
4 | 6 | 8 | ) | @ $ | ^ | ||
3 | 5 | 7 |
| 9 | ! | # | % |
1Main Power Switch
2 System Power Control
3 Power Indicator
4 Headphone Jack
5 Selector Buttons
6 Tone Mode
7 Surround Mode Selector
8 Tuning Selector
9 AM/FM Selector
) Preset Stations Selector
1Main Power Switch: Press this button to apply power to the AVR 125. When the switch is pressed in, the unit is placed in a Standby mode, as indicated by the amber LED 3 surrounding the System Power Control 2. This button MUST be pressed in to operate the unit. To turn the unit off and prevent the use of the remote control, this switch should be pressed until it pops out from the front panel so that the word “OFF” may be read at the top of the switch.
NOTE: This switch is normally left in the “ON” position.
2System Power Control: When the Main Power Switch 1 is “ON,” press this button to turn on the
AVR 125; press it again to turn the unit off. Note that the Power Indicator 3 surrounding the switch will turn green when the unit is on.
3Power Indicator: This LED will be illuminated in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on. When the unit is
!Input Source Selector @ Tuning Mode Selector
# Digital Optical 3 Input $ Digital Coax 3 Input
% Video 3 Video Input Jacks ^ Video 3 Audio Input Jacks & Bass Control
* Balance Control ( Treble Control Ó Volume Control
in operation, the indicator will turn green. Should the indicator turn red, turn the unit off using the Main Power Switch 1 and check the speaker wire con- nections to make certain that there are no short circuits.
4Headphone Jack: This jack may be used to listen to the AVR 125’s output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phone plug. The speakers will automatically be turned off when the headphone jack is in use.
5Selector Buttons: When you are establishing the AVR 125’s configuration settings, use these buttons to select from the choices available, as shown in the Main Information Display Û.
6Tone Mode: Pressing this button enables or dis- ables the Bass and Treble tone controls. When the button is pressed so that the words TONE IN appear in the Main Information Display Û, the
ÔSet Button
Input Indicators Ò Delay
Ú Digital Input Selector Û Main Information Display Ù Channel Select Button ı Speaker Select Button ˆ Test Tone Selector
˜ Surround Mode Indicators ¯ Remote Sensor Window
settings of the Bass & and Treble ( controls may be used to adjust the output signals. When the button is pressed once or twice so that the words TONE OUT appear in the Main Information Display Û, the output signal will be “flat,” without any bass or tre- ble alteration, no matter how the actual Bass and Treble Controls &( are adjusted.
7Surround Mode Selector: Press this button to change the surround mode by scrolling through the list of available modes. Depending on the type of input, some modes are not always available. (See page 22 for more information about surround modes.)
8Tuning Selector: Press the left side of the button to tune
