NOTE: Setting the channel levels while one surround mode is active does not carry over to other modes. After you have set the levels satisfactorily in one mode, note the results and change to other surround modes. For those modes that don’t reflect your level settings, either copy the settings you obtained as

a short cut, or re-do the procedure to determine the correct settings for those surround modes.

Step Five – Configure Sources

This is the last step in the configuration process. In the Installation section, you physically connected various cables between your source devices and the AVR. In this section, you will assign the various audio and video inputs to their sources, ensuring that the AVR uses the correct connections each time you select a source.

Press the OSD Button to view the Master Menu. The cursor will be pointing to the INPUT SETUP line, and you need only press the OK Button to display the Input Setup menu. See Figure 49.

Figure 49 – Input Setup Menu Screen

The first line indicates that the receiver is currently set to the tuner source. You may hear static if the tuner is set to an unused frequency. You will not be able to make any changes to the tuner, other than selecting a component video input or adjusting the tone controls.

It is not recommended that you make either of these changes for the tuner at this time.

Press the ‹ Button to view the next source. The sources will be selected in the following order: Tape, 6-Channel Inputs, AUX, Video 1, Video 2, Video 3, HDMI 3, HDMI 2, HDMI 1, DVD and CD. Pressing the › Button selects the sources in the reverse order.

For each of these sources, you may adjust the following settings. At a minimum, you should make sure that sources connected to any of the component video or digital audio inputs have the correct settings. Other settings are optional, and you may adjust them at a later time when you have more experience with the AVR. Refer to the Table A5 worksheet in the Appendix that you filled out during installation as you assign inputs to each source.

TITLE: You may change the display name for any source (except the tuner). Not only does this enable you to customize your system; it helps you to select the correct source device even when you have forgotten which physical connections you used.

INITIAL SETUP

Move the cursor to the TITLE line and press the OK Button. A block cur- sor will blink. See Figure 50.

Figure 50 – Retitling a Source Input

Use the ⁄/¤ Buttons to scroll through the alphabet in upper and lower case, as well as numbers and a variety of punctuation marks. When you have selected the desired character, press the › Button to move to the next space. You may also press the › Button to leave a blank. Press the OK Button when you have finished spelling out the new display name for the source.

COMPONENT IN: If you connected the source to one of the two component video inputs, and the incorrect set of inputs is displayed at this line, press the › Button to change the setting.

AUDIO IN: See Table A2 in the Appendix for the factory default analog or digital audio inputs assigned to each source. If you used a digital audio connection for a source, change this setting to assign the correct digital audio input, even if you also connected its analog audio outputs to the receiver. Move the cursor to this line, and press the ‹ / › Buttons until the correct digital input appears.

AUTO POLL: The Auto Poll feature is used when both an analog audio and digital audio connection have been made for one source device. If no digital signal is available, the AVR 154 will switch to the analog inputs for the source. This situation can occur with some cable or satellite television broadcasts, where some channels are broadcast with digital audio and others with analog audio, or when a DVD player is paused or stopped.

For some sources, the Auto Poll feature is unnecessary and may be undesirable, such as for a DVD player. Move the cursor to this line, and press the ‹ / › Buttons until OFF appears, disabling the Auto Poll feature. With Auto Poll turned off, the receiver will only check for a signal at the audio input assigned to the source.

The remaining lines in the Input Setup menu activate the tone controls, and may be skipped at this time. We recommend leaving the tone controls at their factory defaults for most listening, in order to enjoy the sound mix created by your favorite movie and music artists. However, if your room or speakers have unusual characteristics, or simply as a matter of personal preference, see the Tone Controls section on page 34 for more information.

You are now ready to begin enjoying your new receiver!

33

Page 32 Page 34
Page 33
Image 33
Harman-Kardon AVR 154 owner manual Step Five Configure Sources, You are now ready to begin enjoying your new receiver
Page 32 Page 34

AVR 154 specifications

The Harman-Kardon AVR 154 is a high-performance audio-video receiver designed for home theater enthusiasts seeking an immersive audio experience. Launched as part of Harman's esteemed line of receivers, the AVR 154 combines sophisticated technology with user-friendly features to create a versatile home entertainment solution.

One of the standout features of the AVR 154 is its multi-channel amplification, delivering a robust output of 50 watts per channel. This power allows for clean and dynamic sound, making it ideal for both movies and music. The AVR 154 supports a 5.1 surround sound configuration, providing an enveloping audio experience that brings films to life. With its ability to decode various surround sound formats, including Dolby TrueHD and DTS-HD Master Audio, it ensures that users enjoy high-quality audio without compromise.

Connectivity is a key aspect of the AVR 154, which offers multiple HDMI inputs, allowing for easy connection to various sources like Blu-ray players, gaming consoles, and streaming devices. With three HDMI inputs and one HDMI output, users have the flexibility to connect multiple devices while enabling audio and video pass-through. The receiver is also equipped with optical and coaxial digital inputs, ensuring compatibility with older audio sources.

Another important feature is the built-in FM/AM tuner, allowing users to access their favorite radio stations without the need for an external receiver. For those who prioritize convenience, the AVR 154 includes an intuitive on-screen display, guiding users through setup and configuration seamlessly. Additionally, the remote control provides easy access to all functions, making operation straightforward.

In terms of design, the Harman-Kardon AVR 154 boasts a sleek aesthetic with a brushed aluminum front panel. The distinctive look, combined with an easy-to-navigate interface, makes it an attractive addition to any home entertainment setup.

Overall, the Harman-Kardon AVR 154 stands out as a reliable and feature-rich AV receiver. With its impressive audio performance, extensive connectivity options, and user-friendly design, it caters to the needs of home theater enthusiasts who seek impactful sound and ultimate flexibility for their entertainment needs. Whether you’re enjoying a thrilling movie or listening to your favorite music, the AVR 154 promises to deliver an exceptional auditory experience.
Top Page Image Contents