OPERATION

Now that you have installed your components and completed a basic configuration, you are ready to begin enjoying your home theater system.

Turning On the AVR 160

Flip the rear-panel Main Power Switch to the “On” position. The Power Indicator on the front panel will turn amber, indicating that the AVR is in Standby mode and is ready to be turned on. The Main Power Switch is normally left on.

There are several ways to turn on the AVR 160:

a)Press the Standby/On Switch on the front panel.

b)Using the remote, press the AVR Power On Button or any of the Source Selectors.

To turn the receiver off, press either the Standby/On Switch on the front panel or the Power Off Button on the remote control. Unless the receiver will not be used for an extended period of time, leave the Main Power Switch on. When the Main Power Switch is turned off, any settings you have programmed will be preserved for up to four weeks.

IMPORTANT NOTE: If the PROTECT message ever appears in the Message Display, turn off the AVR and unplug it. Check all speaker wires for a short. If none is found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again.

Volume Control

Adjust the volume either by turning the knob on the front panel (clockwise to increase volume or counterclockwise to decrease volume), or by pressing the Volume Control on the remote. The volume is displayed as a negative number of decibels (dB) below the 0dB reference point.

0dB is the maximum recommended volume for the AVR 160. Although it’s possible to turn the volume to a higher level, doing so may damage your hearing and your speakers. For certain more dynamic audio materials, even 0dB may be too high, allowing for damage to equipment. Use caution with regard to volume levels.

Mute Function

To temporarily mute all speakers and the headphones, press the Mute Button on the remote. Any recording in progress will not be affected. The MUTE message will appear in the display as a reminder. To restore normal audio, press the Mute Button again, or adjust the volume. Turning off the AVR will also end muting.

Sleep Timer

The sleep timer sets the AVR to play for up to 90 minutes and then turn off automatically.

Press the Sleep Settings Button on the remote, and the time until turn-off will be displayed. Each additional press of the Sleep Button decreases the play time by 10 minutes, with a maximum of 90 minutes. The SLEEP OFF setting disables the sleep timer.

If you press the Sleep Button after the timer has been set, the remaining play time will be displayed. Press the Sleep Button again to change the play time.

tone controls

You may boost or cut either the treble or the bass frequencies by up to 10dB.

Press the Tone Mode Button once. This will indicate whether the tone controls are in or out of the circuitry. With the TONE IN message displayed, press the Tone Mode Button repeatedly to access TREBLE MODE and BASS MODE. Use the KL Buttons to change the treble or bass settings.

To return the tone controls to 0, or “flat” response, press the Tone Mode Button, and then use the KL Buttons to display the TONE OUT message, which preserves any changes you have made to the bass or treble settings for later use. To reactivate your changes, the tone control must be set to TONE IN.

The display will return to normal a few seconds after your last command.

You may also adjust the tone controls using the full-OSD menu system. Press the OSD Button on the remote to view the Master menu. With the cursor pointing to the INPUT SETUP line, press the OK Button to display the Input Setup menu and view the current tone settings. To make changes to the TONE, BASS or TREBLE settings, use the KL Buttons to move the cursor to the setting, and use the M N Buttons to adjust it. It isn’t necessary to press the OK Button to enter the new setting.

When you have finished, either wait until the display times-out and disappears, press the OSD Button to clear the display, or move the cursor to the BACK TO MASTER MENU line and select it to make other changes using the menu system.

NOTE: The AVR 160 does not have a conventional balance control. The speaker output level calibration process compensates for any characteristics of your room or loudspeakers, and it is recommended that you leave the settings as they are after you have completed Initial Setup. However, you may manually adjust the levels of the left and right channels – decreasing one and increasing the other by the same amount – using the Channel Adjust submenu, as described in the Advanced Functions section. This achieves the same effect as a balance control.

26

Page 26
Image 26
Harman-Kardon AVR 160 owner manual Operation

AVR 160 specifications

The Harman-Kardon AVR 160 is a versatile and powerful audio/video receiver that delivers a remarkable home theater experience. Designed for audio enthusiasts and casual listeners alike, this model combines cutting-edge technology, sophisticated design, and intuitive controls.

One of the standout features of the AVR 160 is its robust 7.1-channel surround sound output, which supports the latest audio formats including Dolby TrueHD and DTS-HD Master Audio. This allows users to enjoy a truly immersive sound experience when watching movies or playing video games. With a total power output of 75 watts per channel, the AVR 160 ensures that every sound detail is crystal clear, from explosive action sequences to the softest dialogue.

Another significant aspect of the AVR 160 is its advanced connectivity options. It comes equipped with multiple HDMI inputs, allowing you to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. The HDMI 1.4 version support ensures compatibility with 3D video and offers audio return channel (ARC) functionality, simplifying connections with your TV. Additionally, the receiver features wide compatibility with legacy devices through analog audio inputs, as well as USB ports for direct playback of your music collections.

The AVR 160 also includes Harman's proprietary technology, like the EZSet/EQ automatic speaker calibration system. This feature effortlessly optimizes speaker performance by analyzing the acoustic properties of your room and adjusting settings accordingly. Users can also benefit from the integrated SiriusXM and Spotify support, allowing streaming of music directly through the receiver.

In terms of design, the AVR 160 presents a sleek aesthetic that complements any home entertainment setup. The minimalist front panel, with its bright display and easy-to-use controls, makes operation straightforward. Whether you are adjusting settings or selecting inputs, the receiver’s user-friendly interface enhances the overall experience.

In conclusion, the Harman-Kardon AVR 160 is an exceptional receiver that boasts remarkable audio quality, extensive connectivity options, innovative technologies, and a stylish design. Whether you're a movie enthusiast, music lover, or gaming aficionado, this receiver is well-equipped to meet diverse entertainment needs and elevate your audio experience to new heights.