Using PC Card, PC Card Utility Program | Panasonic CF-71 guide

Using PC Card

24

PC Card Utility Program

About PhoenixCard ManagerTM for Windows® 95

CAUTION

If a ZV card does not operate properly, install PhoenixCard ManagerTM for Win- dows® 95 by following the procedure below, after uninstalling the driver or the appli- cation software for the card.

Otherwise, do not perform the installation; abnormal operation may result.

Installing (only if the ZV card does not operate properly)

1Set [Sound Controller] to [Automatic (PnP)] in the Setup Utility.

2Select [Start] - [Run].

3Type [c:\util\drivers\pccard\setup.exe], press [OK], then follow the on-screen in- structions.

CAUTION

After PhoenixCard ManagerTM for Windows® 95 has been installed, make sure to power off the computer before installing or removing the card. Also, do not use the suspend or hibernation functions if the card is installed.

NOTE

When running the power conservation function with the sound chip set, there may be no sound output. In this case, the following setting needs to be made.

In [Control Panel] - [Power] - [OPL3-SAx power management], set [Non Power

Save mode] then press [Apply]. Then press [OK]. ( page 41)

Uninstalling

When you decide not to use the ZV card, be sure to perform the uninstall proce- dure.

1Uninstall PhoenixCard ManagerTM for Windows® 95 in [Start] - [Settings] - [Con- trol Panel] - [Add/Remove Programs].

2Restart the computer.

3Select [PC Card (PCMCIA)] in [Start] - [Settings] - [Control Panel].

4Press [Next] at the display for the [Display DriverWizard for PC Cards (PCMCIA)], press [Next] again and then press [Finish].

5Shut down the computer by following the on-screen instructions.

Image 24

Panasonic CF-71 manual Using PC Card, PC Card Utility Program, About PhoenixCard ManagerTM for Windows, Uninstalling

Contents

Contents Reference Manual CF-71 Series Key Combinations Key Functions Popup Window LED Indicators Panasonic Hand Writing Touch Pad Drawing Characters or FiguresDetermine the position to begin drawing To next Close the Hand Writing mode Panasonic Hand Writing Touch PadSelect Save As or Save from File Setting the Suspend or Hibernation Function Shutting Down Using the Suspend or Hibernation FunctionSuspend/Hibernation Functions Starting Up Your Computer Quickly Push the sleep switch or Slide the power switch Suspend/Hibernation FunctionsResuming Operation Precautions for Using the Suspend or Hibernation Function When the User Password is set Setting the user password enabling, changing, disablingSecurity Measures Situation Function to use Reference To disable your password Re-enter your password at the Enter User Password AgainWhen the coffee break password is set Security Measures Setting the Coffee break Password enabling or disabling To disable the Coffee break Password Preventing theft of damage to data using a floppy disk ProcedureRun the Setup Utility Using When the supervisor password is set Setting the Supervisor Password To disable your supervisor passwordEnabling, changing, disabling Conserving Power Computing On the RoadThings to Remember Setting Power Management Hibernation with UsingHow to set Advanced and the suspend/hibernation timeout Computing On the Road Power Management settings Battery Power Battery StatusUse the Battery Indicator to Check on the Battery Status Fn + F9 Battery Power When the Remaining Battery Charge Becomes LowSave your data and power off your computer If the suspend or hibernation function is set Replacing the Battery Pack Remove the battery packOpen the display Open the cover Connect the battery pack Connector Tab Label-side up Flat CableWhen closing the cover Close the cover Using a Multimedia Pocket Device Installing/Removing a Multimedia Pocket Device Using a Multimedia Pocket Device Using the Floppy Disk Drive as an External DriveParallel Port FDD Cable Using PC Cards Installing/Removing the PC CardInstalling a PC Card PC Card Using PC Card UninstallingInstalling only if the ZV card does not operate properly PC Card Utility Program Installing/Removing the RAM Module Adding MemoryRAM Module Port Replicator Using a Printer Using an External Display Connect the external display to your computerExternal Display Port + F3 Using USB Devices Run the Setup Utility Using Enter Using USB Devices USB Port Setting for Infrared Data Communications Infrared Data CommunicationsPreparations for Infrared Data Communications Data Communications Installing/Removing the hard disk Removing/Installing the hard diskHard Disk Drive Connector Hard disk DriveRibs Setup Utility Running the Setup UtilityClosing the Program Main Screen Setup Utility System SetupParameters Power Management Power Management Settings Supervisor Setup WSS Codec I/O IRQ Technical Information Network Technical Information Hard DiskSome software will not run normally Non-recognition from other operating systems Reinstallation Power Saving Function in the Sound ChipIt takes a long time to reboot or the computer locks up System module error occurs List of Error Codes Code Description DMI Viewer Running DMI ViewerSaving information to a file Dealing With Problems Battery IndicatorStarting Up Dealing With Problems DisplayDisk Operations Character Input Application SoftwareNetwork Connecting Peripherals Copyright Disclaimer Trademarks