Harman-Kardon MAS 110 Operation, Using the Remote Control, Turning On the MAS 100/MAS

OPERATION

Using the MAS 100/MAS 110 is simple and intuitive. The front-panel controls use advanced touch-sensitive technology. To use the front panel, place a finger over any of the illuminated icons. A gentle tap is all that is necessary. Wait a few seconds for the system to process each command. To remove fingerprints, wipe the front panel with a dry microfiber cloth.

Using the Remote Control

Point the remote at the front of the MAS 100/MAS 110. The remote IR sensor is located on the right half of the front panel of the controller. Do not block the sensor. The remote has a range of approximately 6m, up to 30 degrees off center. If the batteries require replacement, see Step 2 of the Installation section. Use caution and dispose of batteries according to environmental requirements. Never throw the batteries into fire, and remove them from the remote if the remote will be unused for a long period of time.

Turning On the MAS 100/MAS 110

To turn on the MAS 100/MAS 110, press and hold the Power Button on the remote or the controller for 1 second. The system will also turn on when one of the Source Selectors or the Eject Button on the remote is pressed.

Press the Power Button to turn off the system. If the clock has been turned off, the Message Display will go dark to conserve power. Otherwise, the time will be displayed at half-brightness.

2.Press the 7/3 Buttons until “Time Setup” appears in the Message Display.

3.Press the Enter Button to display “Clock”.

Turn the clock on or off: Press the Enter Button and use the 7/3 Buttons to select “On” or “Off”. Turning the clock off conserves power when the system is powered down

to Standby mode.

4.Set the clock: Press the 7/3 Buttons until “Set Clock” appears on the lower line. Press the Enter Button to display “Set Time”.

•Set the time: Press the Enter Button and use the Numeric Keys to enter the hour, then the minute. If the 12-hour time format is active, use the 7/3 Buttons to select “AM” or “PM”. Press the Enter Button to advance from one field to the next without chang- ing it, and press the Enter Button to save the settings.

•Set the format: Press the 7/3 Buttons until “Set 12/24 hour” appears. Press the Enter Button to change the format, and use the 7/3 Buttons to select between the 12- and 24-hour time displays. Press the Enter Button to save the change.

5.Set the day of the week: Press the 7/3 Buttons until “Set Day” appears. Press the Enter Button to display the day of the week, and use the 7/3 Buttons to select the desired day. Press the Enter Button to save the changes.

NOTE: To open a menu or to save new settings press the Enter	Setting the Alarms
button. To advance to the next entry field without changing the value,	For automatic turn-on at a programmed time, set one or both of the
press the Enter Button. To return to the previous menu level without	alarms. The alarms may be set using the Settings Menu. See Figure 3.
making any changes, press the Back Button. These buttons work the	1. Press the Settings Button on the remote.
same way in all menus.
	2. Press the 7/3 Buttons until “Alarm Setup” appears in the Message
Setting the Clock	Display.
The clock may be set using the Settings Menu. See Figure 2.
1. Press the Settings Button on the remote.
Figure 2: Setting the Clock

Right

S e t t i n g s

>

<

S e t t i n g s

>

S p e a k e r S e t u p

T i m e S e t u p

Left

Enter

Back

Right

Right

T i m e S e t u p

>

T i m e S e t u p

>

<

T i m e S e t u p

C l o c k

S e t C l o c k

S e t D a y

Left

Left

Enter

Enter or Back

Enter

Enter or Back

Enter

Back

C l o c k

>

S e t D a y

>

O f f

M o n d a y

Right

S e t C l o c k

S e t C l o c k

S e t T i m e

>

<

S e t 1 2 / 2 4 h o u r >

Left

Enter

Enter or Back

Enter

Enter or Back

S e t T i m e

>

S e t 1 2 / 2 4 h o u r

>

1 2 : 4 3

1 2 h o u r

12