Harman MPMI, MFXI manual FX Processor Controls MFXi only

FX PROCESSOR CONTROLS (MFXi only)

1.Tempo Button - Tapping this button twice sets the Delay Time of the selected program. The LED flashes to indicate current tempo. Can be tapped in time with music source to synchronise the delay.

2.Store Button - Stores program modifications to one of the program locations.

Press and hold for three seconds will store the preset in the current location.

The LED will flash rapidly during the store operation and then stay illuminated for 1 second to show the operation is complete.

3.Pre Delay / Time/ Speed Knob - Controls Pre Delay of the reverbs or the first parameter (time or speed related) of the selected effect. The LED illuminates when the parameter matches the stored setting.

4.Decay / Feedback/Depth Knob - Controls Decay of the reverbs or the second parameter (feedback or depth related) of the selected effect. The LED illuminates when the parameter matches the stored setting.

5.Variation - Controls Liveliness or Diffusion (depending on the reverb selected) or the third parameter of the selected effect. The LED illuminates when the parameter matches the stored setting.

6.Program Select Knob - Navigates through programs, turning to the required program will initiate the loading of the program which take approximately 1 second. The knob can be rotated clockwise or anticlockwise and will alternate between BANK A and BANK B every full rotation. The current bank is shown by its illuminated LED, which flashes if the FX processor is muted. There is a handy aide memoir of the programs printed on the front panel.

7.Clip LED – This LED illuminates when either the incoming audio or the pro- cessed audio (within the effect processor) overloads, and causes distortion of the signal. If this illuminates reduce the FX Master Level (item 25, page 32).

Footswitch Input (not shown on diagram, see item 28 on page 28) - Using a single pole, momentary footswitch inserted into the MUTE FX input the effects processor can be muted/un-muted.

8.MUTE - This switch mutes the output of the FX processor. It doesn’t mute the PFL signal.

9.FX TO AUX 1 - This pot routes a pre-fade signal to the Aux 1-pre bus.

10.FX TO AUX 2- This pot routes a pre-fade and a post-fade signal to the Aux 2-pre and Aux 2-post busses respectively.

11.EFFECTS FADER - This fader controls the level of the signal, from the FX processor, routed to the main mix.

12.PFL - This switch routes a post-effects processor signal to the monitor system.

FX BUS OUT (not shown on diagram, see item 27 on page 28) - This output carries the signal from the FX bus. It could be used as a third Aux Output if desired.

13. ‘SP’ LED - This indicates when a signal is present.

		24-BIT DIGITAL
	A: PRE-DEL	EFFECTS PROCESSOR
	B: TME/SPD		BANKA	BANKB
3		1	S.HALL	SPRING
		2	L.HALL	S.DLY
		3	V.HALL	D.DLY
		4	D.HALL	T.DLY
	A: DECAY	5	S.PLT	P.DLY
		6	L.PLT	M.DLY
	B: FBK/DPTH
		7	V.PLT	R.DLY
4
		8	D.PLT	CHORUS
		9	ROOM	FLANGR
		10	STUDIO	PHASR
		11	CHMBR	TREM/P
	A	12	AMB	VIBRTO
5	B: VARI	13	ARENA	RV/DL S
		14	GATED	RV/DL L
		15	REV	PHSDEL
		16 KARAOKE ROTDEL
				FX TO
9				AUX1
	BANK A
10			0	10
				FX TO
				AUX2
6			0	10
	BANK B			2
	STORE
	TAP			1
	TEMPO
	FX			8
12	MUTE
	PFL
	PK			7

11	SP	13
	0
	-5
	-10

-15

-20

-30

-40

EFFECTS

34 Soundcraft MFXi MPMi User Guide Issue 1210