Harman MFXI, MPMI manual Soundcraft MFXi MPMi User Guide Issue

Models: MFXI

1 60
Download 60 pages 44.83 Kb
Page 17
Image 17
Manual background

12

PEAK LED

This is used to indicate that the signal is close to distorting (clipping) on a specific

 

 

channel.

13

SP LED

The SP LED glows when a signal is present. The feed point for the LED is post-insert,

 

 

pre-EQ.

14

INPUT CHANNEL FADER

This is used to control the level fed to the Mix Bus and post-fade sends.

15

MIX OUTPUTS (XLR)

Connect these to your analogue recording device, or to your amplification &

MONO OUT (¼” Jack)

system.

16 SUB-GROUP OUTPUTS

These outputs can be connected to a separate amplifier system or to an external

(¼” Jack)

processor.

17 SUB-GROUP ROUTING

The sub-group mix can be routed to the main mix, in mono or stereo.

18 MASTER FADERS

These faders control the overall level of the mix and sub-group outputs.

19 MAIN METERS

These show the level of the mix outputs.When the master SOLO LED is lit, the meters

 

 

show the level of the selected AFL/PFL signal.

20 MONITOR OUTPUTS

These are used to feed your monitoring system. This can be directly connected to

(¼” Jack)

powered monitors, or indirectly via an amplifier to standard monitors.

21 MONITOR CONTROL

This controls the level of the signal sent to your monitoring system.

22

MONITOR SELECT SWITCH

This switch selects the signal source to be monitored. Note that the 2-TK input can

 

 

be monitored also, see item 30 below.

23 PHONES CONTROL

This controls the level of the signal sent to the headphones jack socket.

24

HEADPHONES (¼” Jack)

Plug your headphones into this socket. Recommended headphones impedance is

 

 

32 ohms or greater.

25 AUX 1, 2 & 3 OUTPUTS

These outputs can be used to send the channel signal to an artist’s monitors

(¼” Jacks)

(headphones/in-ear/stage monitors), external FX or secondary PA/monitor system.

26 AUX CONTROLS

The rotary controls set the output levels of the three Aux Outputs. The After

& AFL SWITCHES

Fade Listen (AFL) switches route their respective aux output signal to the monitor/

 

 

headphones outputs.

27 AUX 2 POST/PRE SWITCH

This switch globally changes the AUX 2 feed on all the input modules to be either

 

 

post-fade or pre-fade.

28

STEREO INPUTS (¼” Jack)

These two pairs of inputs can be used to connect line level stereo inputs from key-

 

 

boards, sound modules, samplers, computer based audio cards etc. These inputs

 

 

pass through a stereo channel strip, with EQ, Auxes and a Balance control. Mono

 

 

sources may be used by plugging into the left jack only.

29

2-TRACK IN (RCA Phono)

You can connect the playback from your recording device here.

30

2-TRACK OUT

Use these to control the 2 Track signal. The Monitor switch sends the signal to the

 

 

monitor outputs and phones, whilst the TO MIX switch sends it to the main mix.

31

Record Outputs (RCA Phono) You can connect these to the inputs of your recording device.

32 PHANTOM POWER

Press this to globally switch the phantom power (48V) on for condenser microphones.

 

 

WARNING: Do Not apply Phantom Power before connecting a micro-

 

 

phone.

Your MPMi console is equipped with a Kensington® Security slot on the rear panel for use with compatible PC/Laptop security cables. For more information about the Kensington range of security devices please visit http://us.kensington.com

Soundcraft MFXi MPMi User Guide Issue 1210

15

Page 17
Image 17
Harman MFXI, MPMI manual Soundcraft MFXi MPMi User Guide Issue