Installation: Removing unit from skid | 9 |
|
|
How to Reduce the Weight for Installation
1. Remove the top/lid assembly and side panels.
•Note: Removal of the cast hopper lid itself is NOT necessary or recommended.
•Note: The hopper lid must be in the "OPEN" position before the top/lid assembly can be lifted off or reinstalled on the stove body.
•There are (4)
Bolts require a
3/8" socket.
The cast top and lid assembly bolt down bars:
On each side of the stove body, underneath the cast |
| |
top, are (2) 1/4" flange head bolts.See Fig. 12. | (View looking up under the cast top.) | |
These bolts pull the cast top and lid assembly down | Fig. 12 | |
onto the hopper gasket to seal the hopper. | ||
| ||
They also allow for a small amount of front to back |
| |
adjustment for alignment of the top into the wing |
| |
pockets. | Top bolt down bar | |
|
Be careful not to |
| ||
damage | the |
| |
distribution blower |
| ||
located under the | Remove the cast side panels by lifting them upward | ||
insert. There are | |||
off of the hinge pins. See Fig. 13. | |||
guards on | both | ||
| |||
sides of the motor |
| ||
to allow the insert |
| ||
to rest on a flat |
| ||
surface, however, | Top and Lid Assembly | ||
extra care should | |||
| |||
be taken. |
|
|
|
|
|
|
|
|
| Distribution Blower |
|
| |||||||||||
| Protector Angles: These angles are designed to |
|
| |||||||||||||||||
| protect the blower motor from damage when |
|
| |||||||||||||||||
Fig. 10 | placed on a flat surface. Be careful where and |
|
| |||||||||||||||||
how the stove body is handled. |
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Center | Heat |
Medallion | |
| Exchanger |
| Cover |
Mounting Shell | (2) Spring Latches |
|
|
(One on each side) |
| Internal | |
|
| ||
| Ash Pan | Flame Guide | Cast Iron |
| Fig. 11 | (4) pieces | |
|
|