9. Identify the Left Rear Spring Bracket (12) on the left | 9 |
| 16, Grease | ||
Pedal Spring (11). Apply a generous amount of grease |
| ||||
|
| ||||
inside of the Pedal Arm Bushings (37) in the Left Rear |
| 37, |
| ||
Spring Bracket and to the axle on the left Disc |
|
| |||
Crossbar (16). Slide a Spring Spacer (63) onto the |
| Grease |
| ||
axle; make sure that the Spring Spacer is turned so |
|
|
| ||
the flat side is facing the elliptical crosstrainer. |
|
|
| ||
Next, slide the Left Rear Spring Bracket onto the axle. | 11 |
| 63 | ||
Slide a Spring | Bracket Washer (35) onto an M10 x |
| |||
|
| 12 | |||
27mm Patch Screw (40), | and tighten the Patch Screw |
|
| ||
into the axle. |
|
| 40 | 35 | 2 |
Next, hold the lower end of the left Handlebar Leg (5) |
|
| 43 | ||
|
| 7 | |||
inside of the Front Spring Bracket (76) on the left |
|
| |||
|
|
| |||
Pedal Spring (11). Apply grease to an M10 Bolt Set |
|
| 5 | ||
(74). Attach the Handlebar Leg to the Front Spring |
|
|
| ||
Bracket with the Bolt Set. | Do not overtighten the |
|
|
| |
Bolt Set; the Handlebar Leg must pivot freely. |
|
|
| ||
Attach the right Pedal Spring (not shown) to the right | Grease | 76 | 74 | ||
|
| ||||
side of the elliptical crosstrainer in the same way. |
|
|
| ||
Tighten the M6 x 25mm Screw (7) into the Upright (2). | 74 |
| 11 | ||
|
| ||||
Turn the Upright Knob (43) clockwise until it is tight. |
|
|
| ||
See step 7. Tighten the M8 x 45mm Button Bolts (50) |
|
|
| ||
in the Handlebar Legs (5). |
|
|
|
| |
10.Make sure that all parts of the elliptical crosstrainer are properly tightened.Note: Some hardware may
be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical crosstrainer.
INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR
If you purchase the optional chest pulse sensor (refer to page 19), follow the steps below to install the receiver and the short jumper wire included with the chest pulse sensor.
1. Remove the two short screws and the two long screws
from the back of the Console (23). Lift off the front of the Console.
2.Plug the short jumper wire (A) into the indicated jack on the Console (23). Connect the other end of the short jumper wire to the wire on the receiver (B). Note: Any other wires included with the chest pulse sensor
can be discarded.
Next, peel the paper off the adhesive pad on the back of the receiver (B). Orient the receiver as shown, and press it onto the Console (23) in the indicated location.
Refer to step 1 above. Reattach the front of the
Console (23) with the short and long screws. Make sure that no wires are pinched.
1 | 23 | Lift |
| ||
|
| |
|
| Here |
| Short |
|
| Screws |
|
| Long |
|
| Screws |
|
2 | B |
|
|
| |
|
| Cylinder |
23 |
| |
| Jack | A |
8
