PROBLEMSOLUTION

4.The walking belt is off-center or slips when walked on

a.If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the left rear roller adjustment bolt clockwise, and the right bolt counter- clockwise, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b.If the walking belt has shifted to the right, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the left rear roller adjustment bolt counterclockwise, and the right bolt clockwise, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered.

a

b

 

c. If the walking belt slips when walked

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

c

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on, first remove the key and UNPLUG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

THE POWER CORD. Using the allen

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

wrench, turn both rear roller adjustment

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bolts clockwise, 1/4 of a turn. When the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

walking belt is correctly tightened, you

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

should be able to lift the edges of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

walking belt 3 to 4 inches off the walking

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

platform. Be careful to keep the walking

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

belt centered. Plug in the power cord, in-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

sert the key and run the treadmill for a few minutes. Repeat until the walking belt

 

is properly tightened.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5. The displays of the

a. Remove the key from the console and UN-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

console do not func-

PLUG THE POWER CORD. Next, remove

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/8”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tion properly

the screws from the hood and carefully re-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

 

 

 

move the hood. Locate the Reed Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(26) and the Magnet (85) on the left side of

 

 

 

 

 

26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

85

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the Pulley (28). Turn the Pulley until the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Magnet is aligned with the Reed Switch.

 

 

 

 

Top

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Make sure that the gap between the

 

 

 

View

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Magnet and the Reed Switch is about

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/8”. If necessary, loosen the Reed Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Screw (2) and move the Reed Switch slightly. Retighten the Screw. Re-attach the

 

hood and run the treadmill for a few minutes to check for a correct speed reading.

6.Bubbles form in the walking belt

a.Due to variations in humidity and temperature, there is a possibility that bubbles may form in the walking belt. Although the bubbles will disappear with time, you may unplug the power cord, carefully insert a needle into the bubbles, and push the air out of the bubbles.

26

Page 25 Page 27
Page 26
Image 26
Healthrider HRTL16990 manual Displays, Bubbles form in the walking belt
Page 25 Page 27

HRTL16990 specifications

The Healthrider HRTL16990 is an innovative exercise bike designed to enhance your fitness journey, providing an effective cardiovascular workout in the comfort of your home. This model showcases a blend of advanced features, contemporary technologies, and thoughtful design, making it an ideal choice for both fitness enthusiasts and novices.

One of the standout characteristics of the Healthrider HRTL16990 is its adjustable resistance system. Users can easily modify the intensity of their workouts, allowing for a customizable experience that can cater to a range of fitness levels. The bike includes multiple resistance levels, which not only provides versatility but also helps in tracking progress as users increase their stamina and strength over time.

The HRTL16990 is equipped with a built-in LCD display, which provides vital workout metrics such as time, speed, distance, and calories burned. This display allows users to monitor their exercise routines effectively, helping them to stay motivated and achieve their fitness goals. Additionally, the console features pre-set workout programs that cater to different styles and intensities, ensuring that users have a varied and engaging workout experience.

Comfort is paramount in the design of the Healthrider HRTL16990. The bike includes a cushioned seat that can be adjusted to fit various body types, allowing for a comfortable riding position. The handlebars are also designed with grips that make it easier to maintain a stable hold during intense workouts.

Another key feature is the bike's space-saving design. The Healthrider HRTL16990 is compact yet sturdy, making it suitable for small homes or apartments without sacrificing stability or performance. Its easy-to-move frame ensures that users can quickly reposition it as needed.

Furthermore, the Healthrider HRTL16990 promotes a low-impact workout, making it an excellent option for individuals with joint concerns or those recovering from injury. The smooth pedaling motion minimizes stress on the joints, enabling users to exercise regularly without discomfort.

In conclusion, the Healthrider HRTL16990 is an exceptional exercise bike that combines user-friendly features, advanced technologies, and a focus on comfort. With its adjustable resistance, comprehensive tracking capabilities, and ergonomic design, this bike is positioned to help users achieve their fitness objectives effectively and enjoyably. Whether you are looking to start a new fitness regimen or maintain your current routine, the Healthrider HRTL16990 is a worthy addition to your home gym.
Top Page Image Contents