Manuals / Hearth and Home Technologies / Household Appliance / Stove

Hearth and Home Technologies 43M-ACC-MBK, 43ST-ACC warranty Installing Chimney Components

Models: 43M-ACC-MBK 43ST-ACC

1 48
Download 48 pages 58.47 Kb
Page 18
Image 18

4300 Wood Stove Series (ACC)

R

Solid Pack Chimney with Metal Supports as a Thimble (Cont’d)

Min. Chimney Clearance to

 

Wall Spacer and

Min. Clearance

Combustibles - 2 inch (51mm)

2 inch (51mm)

Chimney Flue

1 inch (25mm) Air

Space to Chimney

Liner

Section

Fireclay

Chimney

Liner or

Equivalent

Connector

 

Chimney Section

 

Trim Collar

 

Wall Band

Masonry Chimney

Wall Spacer

 

Constructed to NFPA 211

 

C. Installing Chimney Components

Chimney Connector

Single wall connector or stove pipe.

This must be at least 24 gauge mild steel or 26 gauge blue steel. The sections must be attached to the appliance and to each other with the crimped (male) end pointing toward the stove. All joints, including the connection at the flue collar, should be secured with 3 sheet metal screws. Make sure to follow the minimum clearances to combustibles. Where passage through the wall, or partition of combustible con- struction is desired in Canada, the installation shall conform to CAN/CSA-B365.

Factory-built listed chimney connector (vented).

A listed connector (vented) must be used when installing this unit in a mobile home. The listed connectors must conform to each other to ensure a proper fit and seal.

Figure 18.1

Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (420-480cm) high, (includes stove height) measured from the base of the appliance. The further your stack height or diameter varies from this configuration, the possibility of performance problems exists.

Chimney height may need to be increased by 2 - 3% per each 1000 feet above sea level. It is not recommended to use offsets or elbows at altitudes above 4000 feet above sea level or when there are other factors that affect flue draft.

Crimped

Flue Gas

End

Direction

Toward

 

Stove

 

Secure pipe sections with a

minimum of  screws

Figure 18.2 Chimney Connector (Stove Pipe)

WARNING

Fire Risk.

Inspection of Chimney:

•Chimney must be in good condition.

•Meets minimum standard of NFPA 211

•Factory-built chimney must be 6 inch (152mm) UL103 HT.

WARNING

Asphyxiation Risk.

•Do NOT connect this unit to a chimney flue servicing another appliance.

•Do NOT connect to any air distribution duct or system.

May allow flue gases to enter the house.

WARNING

Fire Risk.

Follow Chimney Connector Manufacturer’s

Instructions for Proper Installation.

ONLY use connector:

•Within the room, between appliance and ceiling or wall. Connector shall NOT pass through:

•Attic or roof space

•Closet or similar concealed space

•Floor or ceiling

Maintain minimum clearances to combustibles

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appli- ance. For assistance or additional information consult a qualified installer, service agency or your dealer.

Page 18

7037-135E

September 1, 2008

Page 17 Page 19
Page 18
Image 18
Hearth and Home Technologies 43M-ACC-MBK, 43ST-ACC warranty Installing Chimney Components
Page 17 Page 19

43M-ACC-MBK, 43ST-ACC specifications

Hearth and Home Technologies has long been a leader in the design and manufacturing of high-quality heating appliances, and their models 43ST-ACC and 43M-ACC-MBK are no exception. These gas fireplaces combine aesthetic appeal with innovative technologies aimed at providing efficient heating solutions for residential spaces.

The 43ST-ACC is designed with versatility in mind. It features a traditional style that can seamlessly integrate into a variety of home decors. One of its standout characteristics is the expansive viewing area that allows homeowners to enjoy the mesmerizing flames. The fireplace utilizes advanced ceramic glass technology that enhances the thermal efficiency, ensuring a warm environment without compromising on safety.

On the technical side, the 43ST-ACC is equipped with the IntelliFire ignition system which provides convenient, reliable startup. This system also allows for enhanced safety features, ensuring the unit operates smoothly and safely. The adjustable flame height and heat output settings further allow users to create their desired ambiance while optimizing fuel consumption.

Additionally, the 43M-ACC-MBK model is geared towards those who appreciate a modern, sophisticated design. This model is characterized by its sleek, black finish and clean lines, making it an eye-catching centerpiece in any room. Like the 43ST-ACC, it also boasts an impressive viewing area, but it comes with the added benefit of customizable features, including remote control operation and programmable thermostats.

Both models are designed with efficiency in mind, incorporating technology that maximizes heat distribution throughout the room. Their direct vent operation ensures that combustion gases are exhausted outside, making them a safe choice for indoor spaces. The inclusion of a blower system in both models enhances air circulation, providing an even distribution of warmth throughout the environment.

In conclusion, the Hearth and Home Technologies 43ST-ACC and 43M-ACC-MBK gas fireplaces combine style, functionality, and advanced technology. Whether you are looking for a traditional touch or a modern flair, these models cater to diverse preferences while ensuring efficient heating and safety. With their innovative features and beautiful designs, they truly represent the pinnacle of home heating solutions. Whether settling in for a cozy evening or entertaining guests, these fireplaces are sure to enhance any living space.