Manuals / Hearth and Home Technologies / Outdoor Cooking / Outdoor Fireplace

Hearth and Home Technologies CASTLEWOOD 42 Installation of Fireplace, Level the Fireplace

Models: CASTLEWOOD 42

1 43
Download 43 pages 18.29 Kb
Page 12
Image 12

4Installation of Fireplace

A. Secure the Fireplace

Position the Fireplace

This fireplace may be placed on either a combustible or noncombustible continouous flat surface. Follow the instructions for framing in Section 3.D. Slide the fireplace into position. Be sure to provide the minimum air clear- ance at the sides and back of the fireplace assembly. See Section 3.B.

WARNING

FIre Risk!

Prevent contact with sagging, loose insulation.

Do NOT instal against vapor barriers or exposed

insulation.

Cooling Air Hoods must be installed if instaling

on a combustible surface.

Level the Fireplace

Level the fireplace side-to-side and front‑to‑back. Shim with noncombustible material, such as sheet metal, as neces- sary. Secure the fireplace (using the nailing flanges located on either side of the fireplace) to the vertical framing.

Note: When elevating the fireplace above the hearth extension the front of the elevated platform must be protected with a protective metal hearth strip.

Important: To ensure proper fit of the glass doors, check the fireplace opening for square. Measure diagonal distances of the opening to make sure they are equal. If they are not, continue to shim the fireplace until those diagonals are equal.

•Place the Protective Metal Hearth Strips

1 in. (25 mm) overlap

Protective metal strips are placed 2 in. (51 mm) under the front of the fireplace and must extend beyond the front and sides of fireplace opening by 2 in. (51 mm).

Figure 4.1 Position the Protective Metal Hearth Strips

Included with your fireplace you will find two metal hearth strips measuring approximately 26 in. x 4 in. (660 mm x 102 mm). These strips are used to provide added protection where the fireplace and the hearth extension meet when installed on a combustible service.

Slide each metal strip 2 in. (51 mm) under the front edge of the fireplace. The individual pieces must overlap each other by 1 in. (25 mm) minimum in the middle of the fireplace to provide continuous coverage of the floor. See Figure 4.1. These metal strips should extend from the front and sides of the fireplace opening by 2 in. (51 mm).

WARNING

Fire Risk!

•Metal hearth strips MUST be installed. Sparks or embers may ignite flooring.

 

Top piece must overlap

 

bottom piece

 

Raised Platform

2 in.

1 in. (25 mm) min.

(51 mm)

overlap

Floor

2 in.

(51 mm)

Figure 4.2 Protect the Front of an Elevated Platform

12

Outdoor Lifestyles by Hearth & Home Technologies Inc. • 4070-300 Rev C • 4/11

Page 11 Page 13
Page 12
Image 12
Hearth and Home Technologies CASTLEWOOD 42 Installation of Fireplace, Secure the Fireplace Position the Fireplace
Page 11 Page 13

CASTLEWOOD 42 specifications

Hearth and Home Technologies has consistently been at the forefront of innovative fireplace solutions, and the CASTLEWOOD 42 is no exception. This exquisite linear gas fireplace is a perfect blend of modern design and advanced technology, making it a sought-after choice for homeowners looking to elevate their living spaces.

One of the standout features of the CASTLEWOOD 42 is its impressive 42-inch width, which allows it to serve as a stunning focal point in both contemporary and traditional interiors. The fireplace is designed with a sleek, clean appearance, featuring large viewing glass and a minimalist frame that creates an unobstructed view of the mesmerizing flames. With its flush-mount design, the CASTLEWOOD 42 can be easily incorporated into a variety of wall configurations, making it versatile enough for any room.

The CASTLEWOOD 42 is powered by advanced Direct Vent technology, ensuring efficient and safe operation. This system allows for the expulsion of combustion gases outside the home, while simultaneously drawing in fresh air for combustion. As a result, the fireplace operates cleanly, providing warmth without compromising indoor air quality. Additionally, the unit is designed to produce up to 30,000 BTUs, delivering sufficient heat to keep spaces cozy during chilly weather.

One of the most impressive aspects of the CASTLEWOOD 42 is its customizable options. Homeowners can choose from a variety of decorative media, such as glass rocks, driftwood, or ceramic logs, to personalize the fireplace and match their decor. The included LED accent lighting enhances the ambience by providing a soft glow that highlights the decorative elements, creating a warm and inviting atmosphere.

Remote control capability is another notable feature of the CASTLEWOOD 42, allowing users to effortlessly adjust the flame height and heat output from the comfort of their couch. Add-on options such as wall-mounted control panels or smartphone integration elevate convenience, ensuring that comfort is just a click away.

The CASTLEWOOD 42 not only excels in aesthetics and functionality but also adheres to high safety standards. With features like tempered glass and a secure venting system, it ensures peace of mind for families. Overall, the Hearth and Home Technologies CASTLEWOOD 42 stands as a testament to quality craftsmanship and innovative design, making it a brilliant addition to any home. Its combination of style, efficiency, and technology proves that fireplaces can be both functional and beautiful.