7Installation of Molded Brick Panel

A. Install Hearth Molded Brick Panel

 

B. Install Back Molded Brick Panel

1. Put a level on fireplace to verify it is level side to side

 

•

 

Refer to Figure 7.4.

and front to back.

 

•

 

Set the grate retainer in place, in the notch in the

2. While the hearth is removed from the fireplace , measure

 

 

 

hearth.

all 4 corrners to determine the variance from corner to

 

• Install the back panel. Center from side to side.

corner. See Figure 7.1.

 

• Install rear refractory retainer.

3. Shim the low corners of the hearth refractory by installing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the metal pieces provided on the fireplace bottom. See

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 7.2.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4. Put a level on the top flange of the refractory and shim as

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

necessary from side to side or front to back. See Figure

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.3.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: The top flange of the hearth should be level to allow

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the sides and back to be installed with minimal gaps. The

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

hearth slopes towards the front of the unit approximately

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/4”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side Refractory Retainer

 

 

 

 

 

 

 

 

Back Refractory Retainer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Back Molded Brick Panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side Refractory Retainer

Left Side Molded Brick Panel

Grate Retainer

Right Side Molded Brick Panel

Figure 7.1.

Hearth Retainer

Figure 7.4

C. Install Side Molded Brick Panel

 

•

Remove screen rods.

 

•

Remove smoke shield

 

• Install side panel by lifting up, setting on top flange of

 

 

hearth and slide towards back of unit until it meets up

 

 

with back panel.

 

•

Install refractory retainer

Figure 7.2.

•

Install second side panel following the steps above.

 

 

Replace the smoke shield.

 

•

Install refractory retainer.

Figure 7.3.

Outdoor Lifestyles by Hearth & Home Technologies Inc. • 4070-300 Rev C • 4/11

19

Page 18 Page 20
Page 19
Image 19
Hearth and Home Technologies CASTLEWOOD 42 owner manual Installation of Molded Brick Panel, Install Side Molded Brick Panel
Page 18 Page 20

CASTLEWOOD 42 specifications

Hearth and Home Technologies has consistently been at the forefront of innovative fireplace solutions, and the CASTLEWOOD 42 is no exception. This exquisite linear gas fireplace is a perfect blend of modern design and advanced technology, making it a sought-after choice for homeowners looking to elevate their living spaces.

One of the standout features of the CASTLEWOOD 42 is its impressive 42-inch width, which allows it to serve as a stunning focal point in both contemporary and traditional interiors. The fireplace is designed with a sleek, clean appearance, featuring large viewing glass and a minimalist frame that creates an unobstructed view of the mesmerizing flames. With its flush-mount design, the CASTLEWOOD 42 can be easily incorporated into a variety of wall configurations, making it versatile enough for any room.

The CASTLEWOOD 42 is powered by advanced Direct Vent technology, ensuring efficient and safe operation. This system allows for the expulsion of combustion gases outside the home, while simultaneously drawing in fresh air for combustion. As a result, the fireplace operates cleanly, providing warmth without compromising indoor air quality. Additionally, the unit is designed to produce up to 30,000 BTUs, delivering sufficient heat to keep spaces cozy during chilly weather.

One of the most impressive aspects of the CASTLEWOOD 42 is its customizable options. Homeowners can choose from a variety of decorative media, such as glass rocks, driftwood, or ceramic logs, to personalize the fireplace and match their decor. The included LED accent lighting enhances the ambience by providing a soft glow that highlights the decorative elements, creating a warm and inviting atmosphere.

Remote control capability is another notable feature of the CASTLEWOOD 42, allowing users to effortlessly adjust the flame height and heat output from the comfort of their couch. Add-on options such as wall-mounted control panels or smartphone integration elevate convenience, ensuring that comfort is just a click away.

The CASTLEWOOD 42 not only excels in aesthetics and functionality but also adheres to high safety standards. With features like tempered glass and a secure venting system, it ensures peace of mind for families. Overall, the Hearth and Home Technologies CASTLEWOOD 42 stands as a testament to quality craftsmanship and innovative design, making it a brilliant addition to any home. Its combination of style, efficiency, and technology proves that fireplaces can be both functional and beautiful.
Top Page Image Contents