Hearth and Home Technologies Soho24B

Heat & Glo • Soho24B • 2137-900 Rev. H • 10/08

8-3/4 in.

222 mm

6-1/2 in.

165 mm

6-5/8 in.

168 mm

6 in.

152 mm

6-1/2 in.

165 mm

6-5/8 in.

168 mm

9-7/8 in.

251 mm

6-1/2 in.

165 mm9-1/4 in.

235 mm

Effective

Height/

Length

Effective Height/Length

Pipe inches mm

SLP4 4 102

SLP6 6 152

SLP12 12 305

SLP24 24 610

SLP36 36 914

SLP48 48 1219

SLP6A 2 - 6 51 - 152

SLP12A 2 - 12 51 - 305

SLP-HVS

Horizontal Pipe

Support

RF4-8

Roof Flashing SLP-FS

Ceiling Firestop

SLP-WS

Wall Shield Firestop

Figure 16.2 SLP Series Vent Components

SLP45

45° Elbow

SLP-PIPE

B. Vent Components Diagrams (continued)

SLP90

90° Elbow

Contents

Main Owners Manual Model: Soho24B NOTICE DO NOT DISCARD Congratulations Listing Label Information/Location Homeowner Reference Information Table of Contents 1 B. Glass Speci cations C. BTU Speci cations 1 A. Appliance Certi cation E. Non-Combustible Materials Speci cation F. Combustible Materials Speci cation G. Electrical Codes H. Requirements for the Commonwealth of Massachusetts 2 A. Design and Installation Considerations 2 C. Inspect Appliance and Components B. Tools and Supplies Needed 3 B. Mantel Projections 3 A. Selecting Appliance Location D. Clearances C. Constructing the Appliance Chase 4 A. Vent Termination Minimum Clearances (See Figure 4.4 for speci c clearances) Measure horizontal clearances from this surface. 4 Measure vertical clearances from this surface. Figure 4.2 speci es minimum vent heights for various pitched roofs. V = VENT TERMINAL X Alcove Applications 5 B. Use of Elbows 5 8-1/2 in. Horizontal A. Vent Table Key C. Measuring Standards 1. Top Vent - Horizontal Termination One Elbow Two Elbows V H D. Vent Diagrams 1. Top Vent - Horizontal Termination - (continued) Three Elbows H V H V 2. Top Vent - Vertical Termination No Elbow Two Elbows V1 = 45 ft Max. (13.72 m) V1 = 3 ft Min. (914 mm) V H 2. Top Vent - Vertical Termination - (continued) Three Elbows V H H 2 V 6 A. Pipe Clearances to Combustibles 6 B. Wall Penetration Framing C. Vertical Penetration Framing D. Install Attic Insulation Shield 7 A. Top Vent ELBOW HEAT SHIELD 7 ELBOW HEAT SHIELD B. Securing and Leveling the Appliance 8 A. Assemble Vent Sections B. Assemble Slip Sections C. Secure the Vent Sections D. Disassemble Vent Sections E. Install Decorative Ceiling Components F. Install Metal Roof Flashing G. Assemble and Install Storm Collar H. Install RF4-8 I. Install Vertical Termination Cap J. Install Decorative Wall Components K. Heat Shield Requirements for Horizontal Termination L. Install Horizontal Termination Cap 9 A. Fuel Conversions B. Gas Pressures C. Gas Connection 9 Page 10 C. Intelli re Ignition System Wiring A. Recommendation for Wire 10 B. Connecting to the Appliance D. Junction Box Installation 11 WARNING WARNING B. Mantel Projections No mantels are allowed when using Studio 24 fronts. 11 12 12 A. Remove Shipping Materials B. Clean the Appliance C. Accessories Stone Placement: Soho24B D. Positioning Stones NO STONES IN THIS AREA WARNING E. Glass Assembly F. Air Shutter Setting G. Re ective Panel 13 A. Before Lighting Appliance 13 CAUTION B. Lighting Instructions (IPI) CAUTION: NOT FOR USE WITH SOLID FUEL WARNING: DO NOT CONNECT 110 VAC TO THE CONTROL VALVE. C. After Appliance is Lit D. Frequently Asked Questions 14 Sympton Possible Cause Corrective Action 14 A. Intelli re Ignition System Intelli re Ignition System - (continued) Symptom Possible Cause Corrective Action 15 15 A. Maintenance Tasks Inspect Maintenance Tasks 16 Appliance Dimensions Table 16 A. Appliance Dimension Diagram Page Page B. Vent Components Diagrams (continued) SOHO24B C. Service Parts Part number list on following page. Soho24B Service Parts at Depot SOHO24B Service Parts at Depot IPI Valve Assembly D. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY D. Limited Lifetime Warranty (continued)