Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TR-OAK-IPI owner manual Service Parts, 9 7, NG, LP Exploded Parts Diagram

Models: 6000TR-OAK-IPI

1 35

Page 4

	6000TR-OAK
Service Parts	6000TR-OAK-IPI

(NG, LP) Exploded Parts Diagram	Beginning Manufacturing Date: 4-01
	Ending Manufacturing Date: 6-06

3

6 Log Set Assembly

9

8 10 11

Part number list on following page.

4	Heat & Glo • 6000TR-OAK, 6000TR-OAK-IPI • 383-901 Rev. K • 5/06

Page 4

Image 4

Heat & Glo LifeStyle 6000TR-OAK-IPI Service Parts, 9 7, NG, LP Exploded Parts Diagram, Beginning Manufacturing Date

Contents

Models 6000TR-OAK 6000TR-OAK-IPI SAFETY AND WARNING INFORMATION PROHIBITEDTABLE OF CONTENTS Service Parts 9 7NG, LP Exploded Parts Diagram 6000TR-OAKService Parts List ACCESSORIES6000TR-OAK, 6000TR-OAK-IPI STANDING PILOT IGNITION ONLYService Parts 6000TR-OAK-IPIIntermittent Pilot Ignition 6000TR-OAK Service PartsValve Assembly Standing Pilot Ignition1Approvals and Codes Installation CodesHigh Altitude Installations Appliance CertificationInstallation of Carbon Monoxide Detectors Pre-installPreparation 2Getting StartedIntroducing the Heat & Glo Gas Fireplaces TOP STANDOFFS 5/063Installing the Fireplace Constructing the Fireplace ChaseStep 1. Locating the Fireplace Horizontal SectionsStep 2. Framing the Fireplace NOTE PIPES OVERLAP 1-1/4INCHES AT EACH JOINT Step 3. Installing the Vent System A. Vent System ApprovalsTEMS OR COMPONENTS MAY BE USED Identifying Vent ComponentsFlue Restrictor Instructions STRAIGHT UP5. Reinstall the Exhaust Shield VENTING WITH ONE 1 90 ELBOW Figure 12. Venting with One 90 ElbowVENTING WITH ONE 1 90 ELBOW Figure 13. Venting with One 90 ElbowVENTING WITH TWO 90 ELBOWS VENTING WITH TWO 2 90o ELBOWSVENTING WITH THREE 3 90 ELBOWS Figure 16. Venting with three 90 elbowsH + H1 H + H1 + H2VENTING WITH THREE 3 90 ELBOWS V + V1 FT+ H1 FT Figure 17. Venting with three 90 elbowsB. Installing Vent Components DVP PIPETo Install the Heat Shield 4.Install Support Brackets3.Continue Adding Vent Components ABOVE THE FIRST 900 ELBOW IN THE VENTING SYSTEM5. Install Firestops C. Vent Termination = AREA WHERE TERMINAL IS NOT PERMITTED Figure 29. Minimum Clearances for Terminations= VENT TERMINAL X = AIR SUPPLY INLETFigure 31. Proper Positioning Step Installing the Optional Heat-Zone-GasKit Step 6. The Gas Control SystemsWARNING THIS UNIT IS NOT FOR USE WITH SOLID FUEL Standing Pilot Ignition SystemStep 7. The Gas Supply Line Step 8. Gas Pressure RequirementsPressure Natural GasStep 9. Wiring the Fireplace Intermittent Pilot Ignition IPI Wiring Operation using Battery PowerOptional Accessories Wall SwitchStep 10. Finishing WARNING WHEN FINISHING THE FIREPLACEFigure 39 Sealant Material Hearth Extensions Installing the Trim Double-checkfor faulty components Air Shutter SettingStep 12. Before Lighting the Fireplace Double-checkfor gas leaks4Maintaining and Servicing Your Fireplace After the InstallationFireplace Maintenance Step 13. Lighting the Fireplace

6000TR-OAK

Service Parts

6000TR-OAK-IPI

(NG, LP) Exploded Parts Diagram

Beginning Manufacturing Date: 4-01

Ending Manufacturing Date: 6-06

3

9