Manuals
/
Heat & Glo LifeStyle
/
Household Appliance
/
Indoor Fireplace
Heat & Glo LifeStyle
AT-ZC manual Burner Flame Patterns, Pilot/Ignitor Flame Patterns
Models:
AT-ZC
1
23
28
28
Download
28 pages
32.53 Kb
20
21
22
23
24
25
26
27
<
>
Install
Diagram of the AT-ZC
Placement of the Ember Material
Maintenance
Connecting the Vent Pipe
Problems, It Is Recommended To Seal
Glass Door Assembly
Errors Can Cause Improper And
Safety
Accessories
Page 23
Image 23
MAKE SURE THE FLAMES
ARE
STEADY—NOT
LIFTING OR FLOATING.
Figure 14. Burner Flame Patterns
STANDING PILOT
3/8" (10 mm)
Figure 15. Pilot/Ignitor Flame Patterns
20
Page 22
Page 24
Page 23
Image 23
Page 22
Page 24
Contents
AT-ZC
Model
Installers Guide
Heat-N-GloFireplace
PROHIBITED
SAFETY AND WARNING INFORMATION
THIS UNIT IS NOT FOR USE WITH SOLID FUEL
Table of Contents
MODEL
Approvals and Codes
and Codes
CERTIFICATION
ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD
Pre-installationPreparation
Introducing the Heat-N-Glo Gas Appliances
Getting Started
VENTING AND INSTALLATION
HEIGHT
Figure 1. Diagram of the AT-ZC
DEPTH
14” 356mm
Vent System Approvals
Installing the Insert
Step Installing the Vent System
Vent System Installation Precautions
Connecting the Vent Pipe
TO AVOID DOWNDRAFTS AND/OR COLD AIR
PROBLEMS, IT IS RECOMMENDED TO SEAL
CAP HAS BEEN INSTALLED
SAFETY. FIGURE 2 SHOWS MINIMUM
STARTING COLLAR OF THE UNIT
Figure
THE EXHAUST PIPE MUST ONLY BE
CONNECTED TO THE EXHAUST
STARTING
EXHAUST
INLET AIR
STARTING
Standing Pilot Ignition System
Step Positioning Leveling, and Securing the
Insert Step The Gas Control Systems
THIS UNIT IS NOT FOR USE WITH SOLID FUEL
Figure 7. Gas Supply Line
Step The Gas Supply Line
DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS
Natural Gas
Step Gas Pressure Requirements Step Wiring the
Fireplace
Pressure
WHEN SERVICING CONTROLS. WIRING
Optional Accessories
Remote Wall Switch
REMOTE WALL SWITCH OR THE
Save the log instructions with this manual
Step Installing Logs and Ember Material
Figure 9. Fan Wiring Diagram
Positioning the Logs
Figure 11. Placement of the Ember Material
Figure 10. GlassAssembly
NOTE REMOVE FRONT TRIM DOOR AND GLASS
Step Installing Trim Surrounds
SURROUND INSTALLATION
ANY MANNER
TOP OF UNIT
MANTEL 12” MAX
12” MAX
Double-checkfor faulty components
Lighting the Appliance After the Installation
Step Before Lighting the Appliance Step
Review safety warnings and cautions
YOUR APPLIANCE
Appliance Maintenance
Maintaining and Servicing Your Appliance
TURN OFF THE GAS BEFORE SERVICING
LIFTING OR FLOATING
Figure 14. Burner Flame Patterns
Figure 15. Pilot/Ignitor Flame Patterns
MAKE SURE THE FLAMES ARE STEADY-NOT
PART DESCRIPTION
Replacement Parts and Accessories
Standing Pilot Only
PART
Grate Assembly
Standing Pilot Continued
Rotory Switch
Glass Door Assembly
PART DESCRIPTION
Accessories
Standing Pilot Cont
PART
ZC-4028-3
Accessories - Continued
ZC-3624-3
ZC-3627-4
DF-ZC36-Carch Door
DF-ZC32-Trim Door
DF-ZC32-CarchTrim Door
DF-ZC36-Trim Door