Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle AT-ZC Standing Pilot Continued, Part Description, Burner, Rotory Switch

Models: AT-ZC

1 28

Page 25

Standing Pilot Continued
PART	PART DESCRIPTION	PART NUMBER
	Burner	SRV485-275A
	Burner Orifice NG	SRV60-800
	Burner Orifice LP	SRV60-801
	Rotory Switch	SRV436-525A
	Glass Door Assembly	GLA-ATZC
	Grate Assembly	SRV485-360A
	Refractory	SRV485-700

Page 25

Image 25

Heat & Glo LifeStyle AT-ZC manual Standing Pilot Continued, Part Description, Burner Orifice NG, Burner Orifice LP

Contents

Installers Guide ModelHeat-N-GloFireplace AT-ZCTHIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONPROHIBITED Table of Contents and Codes Approvals and CodesCERTIFICATION MODELIntroducing the Heat-N-Glo Gas Appliances Pre-installationPreparationGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDVENTING AND INSTALLATION DEPTH Figure 1. Diagram of the AT-ZC14” 356mm HEIGHTStep Installing the Vent System Installing the InsertVent System Installation Precautions Vent System ApprovalsConnecting the Vent Pipe CAP HAS BEEN INSTALLED PROBLEMS, IT IS RECOMMENDED TO SEALSAFETY. FIGURE 2 SHOWS MINIMUM TO AVOID DOWNDRAFTS AND/OR COLD AIRTHE EXHAUST PIPE MUST ONLY BE FigureCONNECTED TO THE EXHAUST STARTING COLLAR OF THE UNITINLET AIR EXHAUSTSTARTING STARTINGInsert Step The Gas Control Systems Step Positioning Leveling, and Securing theTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Standing Pilot Ignition SystemDO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step The Gas Supply LineFigure 7. Gas Supply Line Fireplace Step Gas Pressure Requirements Step Wiring thePressure Natural GasRemote Wall Switch Optional AccessoriesREMOTE WALL SWITCH OR THE WHEN SERVICING CONTROLS. WIRINGFigure 9. Fan Wiring Diagram Step Installing Logs and Ember MaterialPositioning the Logs Save the log instructions with this manualFigure 11. Placement of the Ember Material Figure 10. GlassAssemblySURROUND INSTALLATION Step Installing Trim SurroundsANY MANNER NOTE REMOVE FRONT TRIM DOOR AND GLASS12” MAX MANTEL 12” MAXTOP OF UNIT Step Before Lighting the Appliance Step Lighting the Appliance After the InstallationReview safety warnings and cautions Double-checkfor faulty componentsMaintaining and Servicing Your Appliance Appliance MaintenanceTURN OFF THE GAS BEFORE SERVICING YOUR APPLIANCEFigure 15. Pilot/Ignitor Flame Patterns Figure 14. Burner Flame PatternsMAKE SURE THE FLAMES ARE STEADY-NOT LIFTING OR FLOATINGStanding Pilot Only Replacement Parts and AccessoriesPART PART DESCRIPTIONRotory Switch Standing Pilot ContinuedGlass Door Assembly Grate AssemblyStanding Pilot Cont AccessoriesPART PART DESCRIPTIONZC-3624-3 Accessories - ContinuedZC-3627-4 ZC-4028-3DF-ZC32-CarchTrim Door DF-ZC32-Trim DoorDF-ZC36-Trim Door DF-ZC36-Carch Door

Standing Pilot Continued

PART

PART DESCRIPTION

Burner

SRV485-275A

Burner Orifice NG

SRV60-800

Burner Orifice LP

SRV60-801

Rotory Switch

SRV436-525A

Glass Door Assembly

GLA-ATZC

Grate Assembly

SRV485-360A

Refractory

SRV485-700