E. Install Outside Air Kit

•Keep duct runs short and straight to minimize restriction. A small dip is acceptable for a cold air trap.

•The outside air kit must be installed on the left hand side of the fireplace.

•Locate the outside air hood in a clear area, preferably into prevailing wind during the heating season. Refer to Figure 5.2.

•Install as shown in Figures 7.3 - 7.5.

•The air duct may be run vertically.

•The outside air hood must be at least 3 ft (.91 m) below the top of the uppermost chimney section.

Caution! Risk of Fire or Asphyxiation! Do not draw outside combustion air from wall, floor or ceiling cavity, or enclosed spaces such as an attic or garage.

•Do not place outside air hood close to exhaust vents or chimneys. Fumes or odor could be drawn into the room through the fireplace.

•Locate outside air inlet to prevent blockage from leaves, snow/ice, or other debris. Blockages could cause combustion air starvation.

Flexible Duct (not supplied)

 

 

Outside Air

Outside Air

 

Plate

 

Assembly

Hood

2 Wire Ties

 

•Hearth & Home Technologies Inc recommends using UL181 Class 0 or Class I rigid or flexible ducting.

•Secure flex duct with metal tape, screws or wire ties.

Figure 7.5 Typical Outside Air Installation (BAY-40 will be in- stalled from the bottom of the fireplace)

AK17 Installation (BAY-40)

•Remove the cover plate from the bottom of the fireplace and replace it with outside air plate assembly using existing screws.

•Mark and cut out a 4 1/2 in. (114 mm) diameter hole in the building side for air entry. This hole should allow for some framing (two sides) so the outside air hood assembly may be nailed into position, flush with building’s outside.

•Secure flexible duct (not supplied) to the plate assembly.

•Feed duct through hole to the outside, fasten to the hood assembly.

•Fasten outside air hood assembly to the structure with screws.

Note: To guard against significant cold air infiltration through duct or other parts of system, check for light leaks with a flashlight and seal these with duct tape and/or insulation.

AK14/AK18 Installation (PIER-40)

•The hinge will be toward the front of the fireplace.

•Insert the narrow end of the handle into the upper slot.

•Pivot the handle in the slot toward the hinge.

•Remove the cover plate or knockout from the side of the fireplace and discard. Remove the semi-perforated piece of insulation covering the opening (insulated fireplaces only).

•Partly open the air kit door and insert the handle into the appropriate hole in the side column of the fireplace. The hinge on the door assembly should be located toward the front of the fireplace. If the hinge and the handle are not positioned in this manner, the door will not function correctly.

•Attach the door assembly to the fireplace using the screws provided.

•Check operation by pulling the handle out to open and pushing it in to close.

•Mark and cut out a 4 1/2 in. (114 mm) hole in the building side for air entry. This hole should allow some framing (two sides) so the 4 in. (102 mm) diameter inlet tube assembly may be fastened properly.

•Assemble flexible duct (not supplied) between the door assembly and the inlet tube assembly. Secure it in position with the supplied wire ties.

Heat & Glo • BAY-40, PIER-40 • 34977 • Rev AB 7/12

23

Page 22 Page 24
Page 23
Image 23
Heat & Glo LifeStyle owner manual Install Outside Air Kit, AK17 Installation BAY-40, AK14/AK18 Installation PIER-40
Page 22 Page 24

PIER-40 specifications

The Heat & Glo LifeStyle PIER-40 is a modern gas fireplace designed to enhance any living space while providing superior heating performance. This unit is known for its sleek and contemporary design, making it a popular choice among homeowners and interior designers alike. With its large viewing area, the PIER-40 offers an inviting ambiance that draws people in and creates a warm, cozy atmosphere.

One of the standout features of the PIER-40 is its advanced heating technology. It is equipped with a powerful heater that efficiently distributes warmth throughout the room, ensuring comfortable temperatures even during the coldest months. The adjustable flame height allows users to customize the ambiance, with the option to set the flames to low for a gentle glow or higher for a more robust fire.

Another significant characteristic of the PIER-40 is its versatile design options. Available in various finishes and styles, it can easily complement any decor. The unit can be installed in different configurations, including built-in or as a stand-alone fireplace, providing flexibility in design and placement. The option for glass media instead of traditional logs further adds to its modern appeal.

The LifeStyle series from Heat & Glo emphasizes efficiency and ease of use. The PIER-40 features an intuitive remote control system, allowing users to operate the fireplace from anywhere in the room. This convenience is coupled with an adjustable fan system that helps distribute heat evenly and quickly.

Furthermore, the PIER-40 is built with safety in mind. It includes a safety screen, which minimizes the risk of accidental burns, and features an automatic shut-off mechanism that activates in case of gas leaks or other safety concerns.

In terms of energy efficiency, the PIER-40 is designed to produce a significant amount of heat with minimal gas consumption, making it an eco-friendly option for those looking to reduce their carbon footprint. Overall, the Heat & Glo LifeStyle PIER-40 is a perfect blend of style, technology, and safety, making it an ideal heating solution for modern homes. Its combination of aesthetic appeal, advanced features, and robust performance ensures that it will be a focal point in any room while keeping you warm and comfortable year-round.
Top Page Image Contents