E.Junction Box Installation
If the box is being wired from the OUTSIDE of the appliance:
•Install the Romex™ connector (not included with appliance) in the side wrap.
•Loosen two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.
•Make all necessary wire connections.
If the box is being wired from the INSIDE of the appliance:
•Remove the screw attaching the junction box to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 7.4).
|
|
| HEAT SHIELD |
|
|
|
|
| 14/2WG |
|
|
|
| COPPER GROUND |
|
| WHT | BLK | ATTACHED TO GRN SCREW |
|
|
|
| WITH GRN WIRE |
|
|
| BLK | GREEN WIRE |
|
| WHT | ||
|
|
|
| INSIDE BOX |
|
|
|
| NOTE: Do NOT wire |
|
|
|
| 110VAC to wall switch. |
Figure | 7.4 | Junction Box Detail |
| |
•Pull the electrical wires from outside the appliance through this opening into the valve compartment.
•Loosen the two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.
•Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box.
F.Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall |
|
|
|
|
|
|
| |
mounted switch for use with a fan |
|
|
|
|
|
|
| |
(See Figure 7.5): |
|
|
|
|
|
|
| |
• | The power supply for the |
|
|
|
| 6 INCH |
| |
| appliance must be brought into |
|
|
|
| APPROX. |
| |
|
|
|
|
|
|
|
| |
| a switch box. |
| FAN |
|
|
| WIRE LEAD |
|
|
| SPEED CONTROL |
|
|
| 1 MALE END |
| |
|
| (RHEOSTAT) |
|
|
|
| ||
• The power can then be supplied |
|
|
| 1 FEMALE END |
| |||
|
|
|
|
|
| |||
|
|
|
|
|
|
| ||
| from the switch box to the |
|
|
|
|
| TEMPERATURE |
|
| appliance using a minimum of |
|
|
|
|
|
| |
|
|
|
|
|
| SENSOR SWITCH |
| |
|
|
|
|
|
| WIRE LEAD |
| |
|
|
|
|
|
|
|
| |
• At the switch box connect the |
|
|
|
|
| 2 FEMALE ENDS | JUNCTION | |
|
|
|
|
|
| BOX | ||
| black (hot) wire and red (switch |
|
|
|
|
|
|
|
| leg) wire to the wall switch as |
|
|
|
|
| 6 INCH |
|
| shown. |
|
|
|
|
| APPROX. |
|
|
|
|
| FAN |
|
|
| |
|
|
|
|
|
|
|
| |
• At the appliance connect the |
|
|
|
|
|
|
| |
| black (hot), white (neutral) and |
|
|
|
|
|
|
|
| green (ground) wires to the junc- |
|
|
|
|
|
|
|
| tion box as shown. |
|
|
|
|
|
|
|
• Add a 1/4 inch insulated female |
|
|
| PLUG AND WIRE |
|
|
| |
|
|
| ASSEMBLY |
|
|
| ||
| connector to the red (switch leg) |
|
|
|
|
|
|
|
| wire, route it through the knock- |
|
|
|
|
| OPTIONAL |
|
| out in the face of the junction |
|
|
|
|
|
| |
| Figure | 7.5 Junction Box Wired to Wall Switch | WALL SWITCH |
| ||||
| box, and connect to the top fan |
| ||||||
|
|
|
|
|
|
|
| |
| switch connector (1/4 inch |
|
|
|
|
|
|
|
| male) as shown. |
|
|
|
|
|
|
|
| Heat & Glo LifeStyle Collection | • | Rev. G • | 12/05 | 17 | |||
