F. Tools and Supplies Needed | Heatiator CL36D specification

F. Tools and Supplies Needed

Before beginning the installation be sure the following tools and building supplies are available:

Reciprocating saw	Framing material
Pliers	Non-combustible sealant
Hammer	Gloves
Phillips screwdriver	Framing square
Flat blade screwdriver	Electric drill and bits
Plumb line	Safety glasses
Level	Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws Misc. screws and nails

G. Fireplace System Requirements

This fireplace system requires:

•Fireplace

•Hearth Refractory

•Grate Assembly

•Hearth Extension (required, sold separately)

•Chimney Air Kit (required in Canada)

•Chimney System (required, sold separately)

•Termination Cap (required, sold separately)

H. Inspect Fireplace and Components

Warning! Risk of Fire and/or Explosion! Damaged parts could impair safe operation. Do NOT install dam- aged, incomplete or substitute components. Keep fire- place dry.

•Remove fireplace and components from packaging and inspect for damage.

•Vent system components and doors are shipped in separate packages.

•Report to your dealer any parts damaged in shipment.

•Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12

17

Image 17

Heatiator CL36D F. Tools and Supplies Needed, G. Fireplace System Requirements, H. Inspect Fireplace and Components

Contents

Models CL36D CR36D Wood Burning FireplaceOwner’s Manual Homeowner Reference Information CongratulationsListing Label Information/Location FIREPLACE NO Installer Guide Table of ContentsSafety Alert Key User Guide LIMITED LIFETIME WARRANTY Limited Warranty Hearth & Home Technologies IncWARRANTY COVERAGE WARRANTY PERIOD WARRANTY EXCLUSIONS WARRANTY CONDITIONSThis warranty is void if LIMITATIONS OF LIABILITY A. Appliance Certification 1Listing and Code ApprovalsB. Non-CombustibleMaterials C. Combustible Materials 2Operating Instructions User GuideA. Your Fireplace Hot glass will cause burns C. Starting a Fire B. Seasoned WoodD. Grate E. Firescreen I. Outside Air optional H. Glass DoorsJ. Vented Gas Log Sets & Gas Log Lighters K. Optional Components Hardwood vs Softwood M. Wood FuelMoisture Seasoned Wood B. Chimney Inspection/Cleaning 3Maintenance and ServiceA. Disposal of Ashes Creosote - Formation and Need for Removal C. Check Firebox Refractory E. Glass CleaningD. Inspect Grate Frequency: As desired Start Fire Problems 4Troubleshooting GuideSolution Possible Cause 5Getting Started Installer GuideA. Typical Fireplace System •Illustrations/diagrams are not drawn to scale D. Negative Pressure B. Design and Installation ConsiderationsC. Draft E. Locating Fireplace & Chimney H. Inspect Fireplace and Components F. Tools and Supplies NeededG. Fireplace System Requirements A. Select Fireplace Location 6Framing & Clearances Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 B. Clearances 20 in C. Sidewalls/Surrounds39 deg 50 deg D. Frame the Fireplace A. Things to Consider 7Installation of FireplaceB. Position the Fireplace C. Place Protective Metal Hearth Strips shown, but required in Note: Chimney air kit notCanada Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 E. Install Outside Air Kit 8Chimney Assembly Table A. Chimney Requirements Example B. Using Offsets/ReturnsTable C. Assemble Chimney Sections D. Install Chimney Air KitE. Install Ceiling Firestops F. Install Attic Insulation Shield G. Cut out Hole in Roof H. Complete InstallationI. Install Flashing J. Chimney Termination Requirements A. Construct the Chase 9Chase Installations D. Install Termination Cap B. Install Fireplace & ChimneyC. Install Chase Top •Warning! Risk of Fire! The minimum overlap of •TS345/TS345P Square Termination Cap •TR342 Round Telescoping Termination Cap•ST375 Square Termination Cap •TCT375 Terra Cotta Cap B. Field Constructed Shrouds 10 ShroudsA. Radiation Shield Mailbox Style Shroud radiation shield required Figure 10.4 Roofed Style Shroud DimensionsRoofed Style Shroud radiation shield required Heatilator CL36D, CR36D 12538 Rev Z 7/12 A. Non-combustibleMaterials 11 FinishingB. Combustible Materials C. Hearth Extension Warning! Risk of Fire D. Finishing Material Mantel E. Combustible Mantel Sidewalls/Surrounds A. Gas Log/Lighter Provision 12 AccessoriesB. Wood Burning Inserts Gas Code, ANSI Z223.1 B. Optional Components A. Fireplace Dimensions13 Reference Materials Catalog # C. Chimney Components 368 mm 14-1/2in Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 CL36D D. Service PartsStocked at Depot CR36D D. Service Parts continuedStocked at Depot E. Contact Information – NOTES –DO NOT DISCARD THIS MANUAL DO DISCARDNOT