Sidewalls/Surrounds | Heatiator CL36D manual

F.	Sidewalls/Surrounds
•	Adjacent combustible sidewalls must be located	• Combustible or non-combustible mantel legs, surrounds
	a minimum of 18 in. (457 mm) from the fireplace	and stub walls may be constructed per Figure 11.5.
	opening.

48 in. Min.

36-5/8 in.

16 3/4 in. Minimum

20 in.

50 deg

48 in. Min.

	BRICK
	FRONT
	4 in.
34 in.	14-1/2 in.
	14-1/2 in.
	39 deg
	18 in. Min.

20 in.

50 deg

16 3/4 in. Minimum

14-1/2 in.

39 deg

18 in. Min.

Figure 11.5 Mantel Leg or Wall Projections (acceptable on both sides of opening)

40	Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12

Page 40

Image 40

Heatiator CL36D owner manual Sidewalls/Surrounds

Contents

Owner’s Manual Wood Burning FireplaceModels CL36D CR36D Congratulations Homeowner Reference InformationListing Label Information/Location FIREPLACE NO Table of Contents Installer GuideSafety Alert Key User Guide Limited Warranty Hearth & Home Technologies Inc LIMITED LIFETIME WARRANTYWARRANTY COVERAGE WARRANTY PERIOD WARRANTY CONDITIONS WARRANTY EXCLUSIONSThis warranty is void if LIMITATIONS OF LIABILITY 1Listing and Code Approvals A. Appliance CertificationB. Non-CombustibleMaterials C. Combustible Materials User Guide 2Operating InstructionsA. Your Fireplace Hot glass will cause burns B. Seasoned Wood C. Starting a FireD. Grate E. Firescreen H. Glass Doors I. Outside Air optionalJ. Vented Gas Log Sets & Gas Log Lighters K. Optional Components M. Wood Fuel Hardwood vs SoftwoodMoisture Seasoned Wood 3Maintenance and Service B. Chimney Inspection/CleaningA. Disposal of Ashes Creosote - Formation and Need for Removal E. Glass Cleaning C. Check Firebox RefractoryD. Inspect Grate Frequency: As desired 4Troubleshooting Guide Start Fire ProblemsSolution Possible Cause Installer Guide 5Getting StartedA. Typical Fireplace System •Illustrations/diagrams are not drawn to scale C. Draft B. Design and Installation ConsiderationsD. Negative Pressure E. Locating Fireplace & Chimney G. Fireplace System Requirements F. Tools and Supplies NeededH. Inspect Fireplace and Components 6Framing & Clearances A. Select Fireplace Location B. Clearances Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 C. Sidewalls/Surrounds 20 in39 deg 50 deg D. Frame the Fireplace 7Installation of Fireplace A. Things to ConsiderB. Position the Fireplace C. Place Protective Metal Hearth Strips Note: Chimney air kit not shown, but required inCanada Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 E. Install Outside Air Kit 8Chimney Assembly A. Chimney Requirements Table Table B. Using Offsets/ReturnsExample E. Install Ceiling Firestops D. Install Chimney Air KitC. Assemble Chimney Sections F. Install Attic Insulation Shield I. Install Flashing H. Complete InstallationG. Cut out Hole in Roof J. Chimney Termination Requirements 9Chase Installations A. Construct the Chase B. Install Fireplace & Chimney D. Install Termination CapC. Install Chase Top •Warning! Risk of Fire! The minimum overlap of •TR342 Round Telescoping Termination Cap •TS345/TS345P Square Termination Cap•ST375 Square Termination Cap •TCT375 Terra Cotta Cap A. Radiation Shield 10 ShroudsB. Field Constructed Shrouds Figure 10.4 Roofed Style Shroud Dimensions Mailbox Style Shroud radiation shield requiredRoofed Style Shroud radiation shield required Heatilator CL36D, CR36D 12538 Rev Z 7/12 11 Finishing A. Non-combustibleMaterialsB. Combustible Materials C. Hearth Extension D. Finishing Material Warning! Risk of Fire E. Combustible Mantel Mantel Sidewalls/Surrounds 12 Accessories A. Gas Log/Lighter ProvisionB. Wood Burning Inserts Gas Code, ANSI Z223.1 13 Reference Materials A. Fireplace DimensionsB. Optional Components C. Chimney Components Catalog # 14-1/2in 368 mm Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 D. Service Parts CL36DStocked at Depot D. Service Parts continued CR36DStocked at Depot – NOTES – E. Contact InformationDO NOT DISCARD THIS MANUAL DO DISCARDNOT