Manuals / Hitachi / Computer Equipment / Personal Computer

Hitachi 8000 Elite manual Reconfigure the computer, if necessary

Models: 8000 Elite

1 64

Download 64 pages 7.46 Kb

Page 38

14.Reconfigure the computer, if necessary.

CAUTION: The bottom 5.25-inch drive bay has a shorter depth than the upper two bays. The bottom bay supports a half-height drive or other device that is no more than 14.5 cm (5.7 inches) in depth. Do not try to force a larger drive, such as an optical drive, into the bottom bay. This could cause damage to the drive and the system board. The use of unnecessary force when installing any drive into the drive bay may result in damage to the drive.

9.Connect the power cable (1) and data cable (2) to the rear of the drive. Figure 2-25Connecting the Drive Cables (Optical Drive shown)

10.If you are installing a new drive, connect the opposite end of the data cable to the appropriate system board connector.

NOTE: If you are installing a SATA optical drive, connect the first optical drive to the white SATA connector on the system board labeled SATA1. Connect a second optical drive to the next available (unpopulated) SATA connector following the numbered sequence of the connectors.

If your are installing a media card reader, connect the USB cable to the USB system board connector labeled MEDIA. If the media card reader includes a 1394 port, connect the 1394 cable to the 1394 PCI card.

Refer to System Board Drive Connections on page 30 for an illustration of the system board drive connectors.

11.Replace the front bezel and computer access panel.

12.Reconnect the power cord and turn on the computer.

13.Lock any security devices that were disengaged when the computer access panel was removed.

14.Reconfigure the computer, if necessary.

Installing a 3.5-inch SATA Hard Drive into an Internal Drive Bay

NOTE: The system does not support Parallel ATA (PATA) hard drives.

Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive.

To install a hard drive in a 3.5-inch internal drive bay:

1.Remove/disengage any security devices that prohibit opening the computer.

2.Remove all removable media, such as compact discs or USB flash drives, from the computer.

32 Chapter 2 Hardware Upgrades

ENWW

Image 38

Hitachi 8000 Elite manual Reconfigure the computer, if necessary

Contents

Hardware Reference Guide Hardware Reference Guide About This Book iv About This Book ENWW2 Hardware Upgrades Table of contents1 Product Features Appendix A Specifications 1 Product Features Standard Configuration FeaturesFigure 1-2 Front Panel Components Front Panel Components2 Chapter 1 Product Features ENWWSlot Media Card Reader ComponentsTable 1-2 Media Card Reader Components MediaFigure 1-4 Rear Panel Components Rear Panel Components4 Chapter 1 Product Features ENWWTable 1-4 Keyboard Components Using the Windows Logo KeyKeyboard Table 1-5 Windows Logo Key FunctionsTable 1-5 Windows Logo Key Functions continued 6 Chapter 1 Product FeaturesENWW arrowSerial Number Location Warnings and Cautions 2 Hardware UpgradesServiceability Features Unlocking the Smart Cover Lock Smart Cover FailSafe KeyENWW 10 Chapter 2 Hardware UpgradesFigure 2-1 Removing the Smart Cover Lock Screws Removing the Computer Access Panel 12 Chapter 2 Hardware Upgrades Replacing the Computer Access PanelFigure 2-3 Replacing the Computer Access Panel ENWWRemoving the Front Bezel Removing Bezel Blanks ENWW Replacing the Front BezelFigure 2-6 Replacing the Front Bezel Replacing the Front BezelDDR3-SDRAMDIMMs Installing Additional MemoryDIMMs Populating DIMM Sockets Installing DIMMs on pageInstalling Additional Memory 2 Figure 2-8 Installing a DIMM9.Replace the access panel A DIMM must occupy the black XMM1 socketRemoving or Installing an Expansion Card Figure 2-10 Opening the Expansion Slot Retainer 5.Remove the computer access panelRemoving or Installing an Expansion Card Figure 2-11 Removing an Expansion Slot Cover22 Chapter 2 Hardware Upgrades ENWW17.Reconfigure the computer, if necessary Figure 2-14 Installing an Expansion Card14.Replace the computer access panel Removing or Installing an Expansion CardDrive Positions Removing a Drive from a Drive Bay 26 Chapter 2 Hardware Upgrades ENWWRemoving a Drive from a Drive Bay 7.Remove the drive from the drive bay as followsENWW 8.Store the removed drive in anti-staticpackaging 28 Chapter 2 Hardware UpgradesFigure 2-21 Removing a Hard Drive ENWWInstalling Additional Drives System Board Drive Connections 5.Remove the computer access panel 14.Reconfigure the computer, if necessary ENWW 5.Remove the computer access panelInstalling Additional Drives 10.Replace the computer access panel ENWW Installing Additional DrivesFigure 2-30 Removing the Thermal Sensor 36 Chapter 2 Hardware Upgrades ENWWENWW Installing Additional DrivesFigure 2-33 Replacing the Hard Drive Figure 2-36 Replacing the Carrier Cover 38 Chapter 2 Hardware UpgradesFigure 2-35 Replacing the Thermal Sensor ENWW5.Remove the computer access panel 40 Chapter 2 Hardware Upgrades ENWW5.Remove the computer access panel 42 Chapter 2 Hardware Upgrades ENWWENWW Desktop Dimensions A SpecificationsTable A-1 Specifications Tower DimensionsPower Output Table A-1 Specifications continuedPower Supply 115VB Battery Replacement Type TypeType ENWW 8.Replace the computer access panel48 Appendix B Battery Replacement HP/Kensington MicroSaver Security Cable Lock Installing a Security LockC External Security Devices Figure C-2 Installing a Padlock PadlockHP Business PC Security Lock 50 Appendix C External Security DevicesInstalling a Security Lock ENWWFront Bezel Security 7.Replace the front bezel 9.Replace the access panelInstalling a Security Lock ENWWGrounding Methods D Electrostatic DischargePreventing Electrostatic Damage Computer Operating Guidelines and Routine Care Safety Optical Drive PrecautionsCleaning Shipping PreparationIndex