Drilling to a Specific Depth Fig, Workpiece method | Hitachi B 16RM

DRILLING TO A SPECIFIC DEPTH (Fig. V)

Drilling a blind hole (not all the way through workpiece) to a given depth can be done two ways:

Workpiece method

1.Mark the depth (1) of the hole on the side of the workpiece.

2.With the switch “OFF”, bring the drill bit down until the tip is even with the mark.

3.Hold the feed handle (2) at this position.

4.Spin the lower nut (3) down to contact the depth stop

(4) on the head.

5.Spin the upper nut (5) down and tighten against the lower nut (3).

6.The drill bit will now stop after traveling the distance marked on the workpiece.

Depth scale method

Note: With the chuck quill assembly fully retracted the tip of the drill bit must be just slightly above the top of the workpiece.

1.With the switch “OFF”, turn the feed handle (2) until depth stop (4) points to the desired depth on the depth scale (6) and hold the feed handle in that position.

2.Spin the lower nut (3) down to contact the depth stop

(4).

3.Spin the upper nut (5) against the lower stop nut (3) and tighten.

4.The drill bit will stop after traveling the distance selected on the depth scale.

Fig. V

5

6

3

4

2

1

English

Fig. W

3

2

1

REMOVING CHUCK AND ARBOR (Fig. X)

1.With the switch “OFF” and the unit unplugged, adjust the depth stop nut (1) to hold the drill at a depth of three inches. (See instructions for “LOCKING CHUCK AT DESIRED DEPTH”).

2.Align the key holes in the spindle (2) and quill (3) by rotating the chuck by hand.

3.Insert the key wedge (4) into the key holes (2 & 3).

4.Tap the key wedge (4) lightly with a plastic tipped hammer, until the chuck and arbor fall out of the spindle.

NOTE: Place one hand below the chuck to catch it when it falls out.

Fig. X

2

13

4

LOCKING THE CHUCK AT THE DESIRED DEPTH (Fig. W)

1.With the switch “OFF”, turn the feed handles until the chuck (1) is at the desired depth. Hold the feed handles at this position.

2.Turn the stop nut (2), located under the depth stop (3), counterclockwise and upwards, until it is against the depth stop.

3.The chuck will now be held at this position when the feed handles are released.

— 17 —

Image 17

Hitachi B 16RM Drilling to a Specific Depth Fig, Workpiece method, Depth scale method, Removing Chuck and Arbor Fig

Contents

16RM Hitachi Authorized Service Centers English Product Specifications Before Using this Drill Press SafetyGeneral Safety Instructions Specific Safety Instructions for the Drill Press Guidelines for Extension Cords Grounding Instructions Carton Contents Accessories and Attachments Efgh Mnopq Know Your Drill Press Glossary of Terms Assembly Instructions Assembly and AdjustmentsEstimated Assembly Times 20~40 Minutes Tools Needed Installing the Chuck Fig. G, H Installing the Head Fig. DInstalling Feed Handles Fig. E Bevel Scale Fig. L Drill Press AdjustmentsInstalling Light Bulb Fig. J not included Belt Tension Fig. P Spindle / Quill Fig. NQuill Return Spring Fig. O Basic Drill Press Operations OperationsLaser Guide Avoid Direct EYE Contact Installing a Drill BIT in the Chuck Fig. T On / OFF Switch Panel Fig. SLaser ON/OFF Switch Fig. Q-1 Workpiece method Drilling to a Specific Depth FigDepth scale method Removing Chuck and Arbor Fig Your Protection Basic Operation InstructionsDrill Bit Material Diam Wood Alumi Mild Stain Inches Num Steel Feeding Positioning the Table and Workpiece Fig. Y and ZTilting the Table Fig. AA Lubrication MaintenanceMaintaining Your Drill Press Problem Possible Causes Remedy TroubleshootingTroubleshooting Guide Caracteristiques DU Produit Avant Toute Utilisation DE Cette Perceuse a Colonne SecuriteConsignes Generales DE Securite Consignes DE Securite Specifiques a LA Perceuse a Colonne Veillez à ce que le cordon de rallonge soit correctement Instructions DE Mise a LA MasseConsignes Relatives AUX Rallonges Accessoires Recommandes AccessoiresContenu DE L’EMBALLAGE Deballage ET Verification DU Contenu Efgh Mnopq Connaitre Votre Perceuse a Colonne Boutons DE Blocage DE LA Tension DES Courroies GlossaireEcrous DE Blocage DE L’ECHELLE DE Profondeur Interrupteur MARCHE/ARRET DE LA Perceuse Instructions DE Montage Montage ET ReglageTemps D’ASSEMBLAGE Estime a 20~40 Minutes Outils Necessaires Installation DES Poignees D’ABAISSEMENT Fig. E Echelle D’INCLINAISON Fig. L Installation DE L’AMPOULE Fig. J non fournieReglage DE LA Perceuse a Colonne Tension DES Courroies Fig. P Broche / Fourreau Fig. NRessort DE Retour DU Fourreau Fig. O Evitez Tout Contact Direct Avec LES Yeux LE Laser -GUIDE Utilisation DES Fonctions DE Base DE LA Perceuse a Colonne Fonctionnement Méthode de la pièce à usiner Percer a UNE Profondeur Secifique FigMéthode de l’échelle de profondeur Blocage DU Mandrin a UNE Profondeur Definie Fig. W Enlever LE Mandrin ET L’ARBRE Fig Instructions DES Operations DE BasePour Votre Protection Inclinaison DE LA Table Fig. AA Diamètre Matériau Du foret BoisAcier Pouces Doux Entretenir Votre Perceuse a Colonne EntretienAlimentation Lubrification Probleme Causes Possibles Solution Resolution DES PannesGuide DE Resolution DES Pannes Especificaciones DEL Producto Antes DE Utilizar Esta Taladradora SeguridadInstrucciones Generales DE Seguridad Instrucciones DE Seguridad Específicas Para LA Taladradora Prolongadores Instrucciones DE Conexión a TierraIndicaciones Para LOS Cables Contenido DE LA Caja AccesoriosAccesorios Recomendados Desembalaje Y Comprobación DEL Contenido Efgh Mnopq Conozca SU Taladradora Sumidero Roscado 5/8 Coloque una tubería Glosario DE TérminosTuercas DE Parada DE LA Escala DE Profundidad Instrucciones DE Montaje Montaje Y AjustesTiempo DE Montaje Estimado 20-40 Minutos Herramientas Necesarias Instalación DE LOS Mangos DE Alimentación Fig. E Instalación DEL Cabezal Fig. DInstalación DEL Portabrocas Fig. G, H e Escala DE Bisel Fig. L Ajustes DE LA TaladradoraInstalación DE LA Bombilla Fig. J no se incluye Tensión DE LA Cinta Fig. P EJE / Manguito Fig. NResorte DE Vuelta DEL Manguito Fig. O Funciones Básicas DE LA Taladradora FuncionesEL Laser -GUIDE Evite EL Contacto Ocular Directo Instalación DE LAS Brocas EN EL Portabrocas Fig. T Panel DE Interruptor on / OFF Fig. SInterruptor ON/OFF DEL Láser Fig. Q-1 Extracción DEL Portabrocas Y DEL Árbol Fig Método de escala de profundidadBloqueo DEL Portabrocas a LA Profundidad Deseada Fig. W SU Protección Instrucciones Básicas DE Fundionamiento Alimentación Coloque LA Mesa Y LA Pieza DE Trabajo Fig. Y y ZInclinación DE LA Mesa Fig. AA Lubricación MantenimientoMantenimiento DE LA Taladradora Problema Causas Posibles Solución Solución DE ProblemasGuía DE Solución DE Problemas Parts List Drill Press Model NO. B16RM Page Page Hitachi Koki Canada Co