English
CAUTION:
Always secure the workpiece with the right hand side for compound cutting. Never rotate the table to the right for compound cutting, because the saw blade might then contact the clamp or vise that secures the workpiece, and cause personal injury or damage.
7.Crown molding cutting procedures
Fig. 24 shows two common crown molding types having angles of (θ) 38° and 45°.
For the typical crown molding fittings, see Fig. 25.
upper surface Ceiling
Ceiling
Wall
1 2
Inside corner
Fig. 25
34
Outside corner
lower surface
Wall
Fig. 24
The table below shows the miter angle and the bevel angle settings that are ideal for the two crown molding types.
NOTE:
For convenience, positive stops are provided for the miter setting (left and right 31.6°) positions.
For miter cut setting
If the turntable has been set to either of the angles described, move the turntable adjusting side handle a little to the right and left to stabilize the position and to properly align the miter angle scale and the tip of the indicator before the operation starts.
For bevel cut setting
Move handle on bevel section to the left and check that the position is stable and that the bevel angle scale and the tip of the indicator are properly aligned. Then tighten the clamp lever.
| To process crown molding at | To process crown molding at positions 2 | ||||||||||
Type of Crown | positions 1 and 4 in Fig. 36. | and 3 in Fig. 36. |
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| |
Molding | Miter Angle | Bevel Angle | Miter Angle | Bevel Angle | ||||||||
| ||||||||||||
| Setting | Setting | Setting | Setting | ||||||||
|
|
|
|
| ||||||||
45° Type | right 35.3° | left 30° | left 35.3° | left 30° | ||||||||
( |
| mark) | ( |
| mark) | ( |
| mark) | ( |
| mark) | |
|
|
|
|
| ||||||||
|
|
|
|
| ||||||||
38° Type | right 31.6° | left 33.9° | left 31.6° | left 33.9° | ||||||||
( |
| mark) | ( |
| mark) | ( |
| mark) | ( |
| mark) | |
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
(1)Setting to cut crown moldings at positions 1and 4in Fig. 25 (see Fig. 26; tilt the motor head to the left):
1Turn the turntable to the right and set the Miter Angle as follows:
*For 45° type crown moldings: 35.3° ( 
mark)
* For 38° type crown moldings: 31.6° ( mark)
2Tilt the motor head to the left and set the Bevel Angle as follows:
* | For 45° type crown moldings: | 30° ( |
| mark) | |
* | For 38° type crown moldings: | 33.9° | ( |
| mark) |
3Position the crown molding so that the upper surface (
in Fig. 24) contacts the fence as indicated in Fig. 28.
(2)Setting to cut crown moldings at positions 2and 3in Fig. 25 (see Fig. 27; tilt the head to the left):
1Turn the turntable to the left and set the Miter Angle as follows:
*For 45° type crown moldings: 35.3° ( 
mark)
* For 38° type crown moldings: 31.6° ( mark)
2Tilt the head to the left and set the Bevel Angle as follows:
*For 45° type crown moldings: 30° ( 
mark)
* For 38° type crown moldings: 33.9° ( mark)
3Position the crown molding so that the lower surface (
in Fig. 24) contacts the fence as in Fig. 29.
Head
Head
Bevel angle scale
3 2 
Fence (B)
Base
Turntable
Miter angle scale
Fig. 27
Fence
1 | Bevel angle scale | Table on base |
| ||
| Fig. 28 | |
|
| |
| 4 | Fence |
| Fence (A) | |
|
| |
Miter angle scale |
|
|
| Base | Table on base |
Turntable
Fig. 29
Fig. 26
12