English

OPTIONAL ACCESSORIES...sold separately

1Extension Holder and Stopper (Code No. 322710)

2Saw blade 10 in. (255mm) TCT Saw blade for wood cut (Total teeth: 60) (Code No. 976472)

3Saw blade 10 in. (255mm) TCT Saw blade for aluminum cut (Total teeth: 100) (Code No. 319658)

4Crown molding Vise Ass’y (Code No. 322712) (Include Crown molding Stopper (L))

5Crown molding Stopper (L) (Code No. 322713)

6 Crown molding Stopper (R) (Code No. 322714)

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

APPLICATIONS

Wood and aluminum sash.

PREPARATION BEFORE OPERATION

Make the following preparations before operating the power tool: 1. Installation

16-3/8 in. (416mm)

M6 ⋅ 20 Screw

Clamp lever

6mm Bolt

Holder (B)

Adjust the holder

 

until its bottom

Move

surface contacts the

 

work bench surface.

 

Fig. 5-a

Install the side handle

Remove the M10 bolt and install the side handle that came enclosed with this unit.

11/32 in. (9mm)

1/4-8 in.

(210mm)

4 Holes

 

 

14-1/6 in. (360mm)

benchThick

 

Base

 

 

 

5/16 in. (8mm)

(25mm)in.1

 

Bolt

 

 

 

Work bench 5/16 in. (8mm) Nut

Fig. 4

Attach the power tool to a level, horizontal work bench in accordance with Fig. 4.

Select 5/16 in. (8mm) diameter bolts suitable in length for the thickness of the work bench.

Bolt length should be at least 1-3/8 in. (35mm) plus the thickness of the work bench.

For example, use 2-11/32 in. (60mm) or larger bolts for a 1 in. (25mm) thick work bench.

The holder attached to the rear of the base helps stabilize the power tool.

Holder (B), clamp lever adjustment:

Attach the included holder (B) in the position as shown in figure 5 and adjust the holder (B) until its bottom surface contacts the work bench surface. After adjustments, securely tighten the 6mm bolt with the included 10mm box wrench. Loosen the M6 ⋅ 20 screw on the clamp lever and attach to a position where the clamp lever can be easily operated.

CAUTION:

Attach the power tool to a work bench with bolts (6mm), and if the turntable has been swiveled 45° degrees or more, be careful not to let the hand that is holding the side handle get caught between the side handle and heads of bolts (6mm). Injuries could result.

M10 Bolt

Fig. 5-b

Install the sub fence (B)

In the case of direct angle cutting and angle cutting, use the sub fence. The sub fence (B) can be installed on the right side of the guide fence (B). Place the attached plate (A) in the position as shown in figure 5-c, insert the tip in the groove of fence (B) and simultaneously, insert flathead screw M6 into fence (B), sub fence (B), and plate (A), then tighten nylon nut M6 with the included 10mm box wrench until the sub fence (B) can smoothly rotate. Then, you can realize stable cutting of the material with a wide back face.

M6 Flat screw

Sub fence (B) Plate (A)

M6 Nylon nut

Fence (B)

Fig. 5-c

2.Releasing the locking pin

When the power tool is prepared for shipping, its main parts are secured by a locking pin.

Move the handle slightly so that the locking pin can be disengaged.

NOTE:

Lowering the handle slightly will enable you to disengage the locking pin more easily and safely.

The lock position of the locking pin is for carrying and storage only.

7