Hitachi C 15FB BEFORE CUTTING

12

English

BEFORE CUTTING

1. Cutting a groove on the table insert

A groove has to be cut in the table insert, before starting opera-

tion. Secure a piece of wood about 5" (125 mm) wide to the turnta-

ble with the vise (A), to prevent the breakage of the table insert.

After the switch has been turned on and the saw blade has reached

its maximum speed, slowly lower the handle to cut the piece of

wood, and then a groove on the table insert.

CAUTION: Do not cut the groove too quickly; otherwise the

guard might become damaged.

2. Checking the saw blade lower limit position

Check that the saw can be lowered 1 - 1/4" to 1 - 5/16" (32 mm to

33 mm) below the table insert.

If necessary, adjust as follows:

(1) Loosen the 10mm lock nut on the 10mm depth adjustment bolt.

(2) Turn the 10mm depth adjustment bolt as necessary to set the

lower limit position. The saw blade goes up when the 10mm

depth adjustment bolt is turned counterclockwise and down

when it is turned clockwise.

(3) Once the adjustment is complete, fully tighten the 10mm lock

nut.

NOTE: Before tightening the 10mm lock nut, confirm that the

saw blade is adjusted so that it will not cut into the turn-

table. Allow a space of 3/16" (4 - 5 mm) between the saw

blade and the turntable.

3. Securing the workpiece

WARNING: Always clamp or vise to secure the workpiece to the fence; otherwise the workpiece

might be thrust from the table and cause bodily harm.

4. Installing the holders (Standard accessory)

The holders help keep longer workpieces stable and in place dur-

ing the cutting operation.

Install them on the right and left sides of the base and fix them

with 10 mm bolts.

For moving the holders, loosen the 10 mm bolts.

Fig. 7

Table Insert Turntable

Fig. 8

Up

Down

10mm Depth

adjustment bolt

Fig. 9

Holder

10 mm Bolt

Vise (A)

Contents

Main MODEL MITER SAW MODELE SCIE A COUPE DONGLET MODELO INGLETEADORA C 15FB INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS WARNING MODE DEMPLOI ET INSTRUCTIONS DE SECURITE AVERTISSEMENT CONTENTS TABLE DES MATIERES NDICE IMPORTANT INFORMATION MEANINGS OF SIGNAL WORDS SAFETY INPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS Page Page REPLACEMENT PARTS USE PROPER EXTENSION CORD Page English OPERATION AND MAINTENANCE Fig. 2 NOTE: NAME OF PARTS Fig. 1 SPECIFICATIONS For how to cut materials marked *, refer to page 15: 4. Cutting wide workpiece. APPLICATIONS PREPARATION BEFORE OPERATION 1. Installation 2. Releasing the locking pin NOTE: BEFORE USING BEFORE CUTTING 1. Cutting a groove on the table insert CAUTION: 2. Checking the saw blade lower limit position NOTE: 5. Stopper for precision cutting (Standard accessory) 6. Handle position adjustment 7. Using an ink line WARNING: PRACTICAL APPLICATIONS WARNING: 1. Switch operation WARNING: 2. Cutting Operation 3. Miter cutting procedures NOTE: CAUTION: 4. Cutting wide workpiece CAUTION: SAW BLADE MOUNTING AND DISMOUNTING WARNING: 1. Mounting the saw blade (Fig. 24-a, Fig. 24-b and Fig. 25) NOTE: WARNING: MAINTENANCE AND INSPECTION WARNING: 1. Inspecting the saw blade CAUTION: 2. Inspecting the carbon brushes (Fig. 26, 27) SERVICE AND REPAIRS INFORMATIONS IMPORTANTES SIGNIFICATION DES MOTS DAVERTISSEMENT SECURITE CONSIGNES DE SECURITE RELATIVES AUX OUTILS ELECTRIQUES. Page Consignes de scurit spciales pour cet outil lectrique Page Page UTILISATION ET ENTRETIEN REMARQUE: NOM DES PICES Franais SPCIFICATIONS APPLICATIONS PRPARATION AVANT LUTILISATION 1. Installation REMARQUE: 3. Installer le sac copeaux, le support, la bute et les taux. AVANT LUTILISATION AVANT LA COUPE 1. Dcoupe dune encoche dans la plaque dinsertion ATTENTION: 2. Vrification de la position de limite infrieure de la lame REMARQUE: 5. Bute pour la prcision de coupe (Accessoire standard) 6. Rglage de la position de la poigne 7. Utilisation dun trait dencre AVERTISSEMENT: APPLICATIONS PRATIQUES AVERTISSEMENT: 1. Fonctionnement de linterrupteur AVERTISSEMENT: 2. Coupe 3. Procdure de coupe donglet REMARQUE: ATTENTION 4. Planche de bois ATTENTION: INSTALLATION ET RETRAIT DE LA LAME AVERTISSEMENT: 1. Installation de la lame (Fig. 24-a, Fig. 24-b et Fig. 25) REMARQUE: AVERTISSEMENT: ENTRETIEN ET INSPECTION AVERTISSEMENT: 1. Inspection de la lame ATTENTION: 2. Inspecter les balais carbone (Fig. 26 et Fig. 27) SERVICE APRS-VENTE ET RPARATIONS INFORMACIN IMPORTANTE SIGNIFICADO DE LAS PALABRAS CLAVE SEGURIDAD NORMAS DE SEGURIDAD PARA LAS HERRAMIENTAS ELCTRICAS Page Normas de seguridad especficas para la utilizacin de esta herramienta Page PIEZAS DE REEMPLAZO UTILICE EL CABLE PROLONGADOR ADECUADO ADVERTENCIA: AISLAMIENTO DOBLE PARA OFRECER UNA OPERACIN MS SEGURA GUARDE ESTAS INSTRUCCIONES A MANO PARA QUE PUEDAN USARLAS OTROS QUE DESEEN UTILIZAR ESTA HERRAMIENTA Espaol OPERACIN Y MANTENIMIENTO Fig. 2 NOTA: NOMENCLATURA DE PARTES Fig. 1 ESPECIFICACIONES Para cortar materiales marcados con *, consulte la pgina 47:4. Peligroso. APLICACIONES PREPARATIVOS PREVIOS A LA OPERACIN 1. Instalacin 2. Liberacin del pasador de bloqueo NOTA: ANTES DE LA UTILIZACIN ANTES DEL CORTE 1. Corte de una ranura en el inserto de la mesa PRECAUCIN: No corte la ranura con demasiada rapidez, 2. Comprobacin de la posicin lmite inferior de la hoja de sierra NOTA: 5. Retn para precisin de corte (Accesorio estndar) 6. Ajuste de la posicin de la empuadura 7. Utilizacin de una lnea de tinta ADVERTENCIA: APLICACIONES PRCTICAS ADVERTENCIA: 1. Operacin de conmutacin ADVERTENCIA: 2. Operacin de corte 3. Procedimiento de corte de ingletes NOTA: PRECAUCIN: Cuando el tornillo de carpintero (A) est montado a la izquierda de la base, como 4. Peligroso PRECAUCIN: Como la pieza de trabajo necesita sujetarse MONTAJE Y DESMONTAJE DE LA HOJA DE SIERRA ADVERTENCIA: 1. Montaje de la hoja de sierra (Fig. 24-a, Fig. 24-b y Fig. 25) NOTA: ADVERTENCIA: MANTENIMIENTO E INSPECCIN ADVERTENCIA: 1. Inspeccin de la hoja de sierra PRECAUCIN: No utilice nunca una hoja de sierra mellada. Cuando la hoja de sierra est mellada, 2. Inspeccion las de escobillas (Figs. 26 y 27) SERVICIO Y REPARACIONES NOTA: Page Page Page Hitachi Koki Canada Co.