Hitachi C 15FB SERVICE AND REPAIRS

18

English

4. Inspecting the safety cover for proper operation

Before each use of the tool, test the safety cover (see Fig. 6) to assure that it is in good condition and

that it moves smoothly.

Never use the tool unless the safety cover operates properly and it is in good mechanical condition.

5. Storage

After operation of the tool has been completed, check that the following has been performed:

(1) Trigger switch is in OFF position,

(2) Power plug has been removed from the receptacle,

(3) Lock-off button has been removed and stored in a secure place.

When the tool is not in use, keep it stored in a dry place out of the reach of children.

6. Lubrication

Lubricate the following sliding surfaces once a month to keep the power tool in good operating condi-

tion for a long time (see Fig. 1 and Fig. 2). Use of machine oil is recommended.

Oil supply points:

*Rotary portion of hinge

*Rotary portion of vise assembly

*Rotary portion of turntable and base (See Fig. 28)

7. Cleaning

Periodically remove chips, dust and other waste material from the surface of the power tool, especially

from the inside of the safety cover with a damp, soapy cloth. To avoid a malfunction of the motor,

protect it from contact with oil or water.

SERVICE AND REPAIRS

All quality power tools will eventually require servicing or replacement of parts because of wear from

normal use. To assure that only authorized replacement parts will be used and that the double insula-

tion system will be protected, all service (other than routine maintenance) must be performed by an

AUTHORIZED HITACHI POWER TOOL REPAIR CENTER ONLY.

NOTE: Specifications are subject to change without any obligation on the part of HITACHI.

Fig. 28

Oil supply points

Contents

Main MODEL MITER SAW MODELE SCIE A COUPE DONGLET MODELO INGLETEADORA C 15FB INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS WARNING MODE DEMPLOI ET INSTRUCTIONS DE SECURITE AVERTISSEMENT CONTENTS TABLE DES MATIERES NDICE IMPORTANT INFORMATION MEANINGS OF SIGNAL WORDS SAFETY INPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS Page Page REPLACEMENT PARTS USE PROPER EXTENSION CORD Page English OPERATION AND MAINTENANCE Fig. 2 NOTE: NAME OF PARTS Fig. 1 SPECIFICATIONS For how to cut materials marked *, refer to page 15: 4. Cutting wide workpiece. APPLICATIONS PREPARATION BEFORE OPERATION 1. Installation 2. Releasing the locking pin NOTE: BEFORE USING BEFORE CUTTING 1. Cutting a groove on the table insert CAUTION: 2. Checking the saw blade lower limit position NOTE: 5. Stopper for precision cutting (Standard accessory) 6. Handle position adjustment 7. Using an ink line WARNING: PRACTICAL APPLICATIONS WARNING: 1. Switch operation WARNING: 2. Cutting Operation 3. Miter cutting procedures NOTE: CAUTION: 4. Cutting wide workpiece CAUTION: SAW BLADE MOUNTING AND DISMOUNTING WARNING: 1. Mounting the saw blade (Fig. 24-a, Fig. 24-b and Fig. 25) NOTE: WARNING: MAINTENANCE AND INSPECTION WARNING: 1. Inspecting the saw blade CAUTION: 2. Inspecting the carbon brushes (Fig. 26, 27) SERVICE AND REPAIRS INFORMATIONS IMPORTANTES SIGNIFICATION DES MOTS DAVERTISSEMENT SECURITE CONSIGNES DE SECURITE RELATIVES AUX OUTILS ELECTRIQUES. Page Consignes de scurit spciales pour cet outil lectrique Page Page UTILISATION ET ENTRETIEN REMARQUE: NOM DES PICES Franais SPCIFICATIONS APPLICATIONS PRPARATION AVANT LUTILISATION 1. Installation REMARQUE: 3. Installer le sac copeaux, le support, la bute et les taux. AVANT LUTILISATION AVANT LA COUPE 1. Dcoupe dune encoche dans la plaque dinsertion ATTENTION: 2. Vrification de la position de limite infrieure de la lame REMARQUE: 5. Bute pour la prcision de coupe (Accessoire standard) 6. Rglage de la position de la poigne 7. Utilisation dun trait dencre AVERTISSEMENT: APPLICATIONS PRATIQUES AVERTISSEMENT: 1. Fonctionnement de linterrupteur AVERTISSEMENT: 2. Coupe 3. Procdure de coupe donglet REMARQUE: ATTENTION 4. Planche de bois ATTENTION: INSTALLATION ET RETRAIT DE LA LAME AVERTISSEMENT: 1. Installation de la lame (Fig. 24-a, Fig. 24-b et Fig. 25) REMARQUE: AVERTISSEMENT: ENTRETIEN ET INSPECTION AVERTISSEMENT: 1. Inspection de la lame ATTENTION: 2. Inspecter les balais carbone (Fig. 26 et Fig. 27) SERVICE APRS-VENTE ET RPARATIONS INFORMACIN IMPORTANTE SIGNIFICADO DE LAS PALABRAS CLAVE SEGURIDAD NORMAS DE SEGURIDAD PARA LAS HERRAMIENTAS ELCTRICAS Page Normas de seguridad especficas para la utilizacin de esta herramienta Page PIEZAS DE REEMPLAZO UTILICE EL CABLE PROLONGADOR ADECUADO ADVERTENCIA: AISLAMIENTO DOBLE PARA OFRECER UNA OPERACIN MS SEGURA GUARDE ESTAS INSTRUCCIONES A MANO PARA QUE PUEDAN USARLAS OTROS QUE DESEEN UTILIZAR ESTA HERRAMIENTA Espaol OPERACIN Y MANTENIMIENTO Fig. 2 NOTA: NOMENCLATURA DE PARTES Fig. 1 ESPECIFICACIONES Para cortar materiales marcados con *, consulte la pgina 47:4. Peligroso. APLICACIONES PREPARATIVOS PREVIOS A LA OPERACIN 1. Instalacin 2. Liberacin del pasador de bloqueo NOTA: ANTES DE LA UTILIZACIN ANTES DEL CORTE 1. Corte de una ranura en el inserto de la mesa PRECAUCIN: No corte la ranura con demasiada rapidez, 2. Comprobacin de la posicin lmite inferior de la hoja de sierra NOTA: 5. Retn para precisin de corte (Accesorio estndar) 6. Ajuste de la posicin de la empuadura 7. Utilizacin de una lnea de tinta ADVERTENCIA: APLICACIONES PRCTICAS ADVERTENCIA: 1. Operacin de conmutacin ADVERTENCIA: 2. Operacin de corte 3. Procedimiento de corte de ingletes NOTA: PRECAUCIN: Cuando el tornillo de carpintero (A) est montado a la izquierda de la base, como 4. Peligroso PRECAUCIN: Como la pieza de trabajo necesita sujetarse MONTAJE Y DESMONTAJE DE LA HOJA DE SIERRA ADVERTENCIA: 1. Montaje de la hoja de sierra (Fig. 24-a, Fig. 24-b y Fig. 25) NOTA: ADVERTENCIA: MANTENIMIENTO E INSPECCIN ADVERTENCIA: 1. Inspeccin de la hoja de sierra PRECAUCIN: No utilice nunca una hoja de sierra mellada. Cuando la hoja de sierra est mellada, 2. Inspeccion las de escobillas (Figs. 26 y 27) SERVICIO Y REPARACIONES NOTA: Page Page Page Hitachi Koki Canada Co.