When you think something wrong
Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer.
Phenomena | Cause | Check point | Page | |
|
|
|
| |
| ∙The Main power is not turned on. | ∙Turn the MAIN POWER switch on. | P.13 | |
| ∙The power cord is disconnected. | ∙Insert the power cord into an AC socket. | P.9 | |
Power cannot be | ∙60 seconds have not elapsed since the | ∙When the power is turned off turn the power | P.13 | |
power was turned off. | switch on after waiting at least 60 seconds. |
| ||
turned on. | P.6 | |||
∙Inside the projector too hot. | ∙Do not block the ventilation holes. | |||
| ||||
|
| ∙Clean the air filter. | P.29 | |
|
| ∙Use the projector under 35°C temperature. |
| |
No picture and | ∙The setting of the input source is not | ∙Set the correct input using the input select button | P.8, 10, | |
correct. | of the projector or the remote control. | 13, 18 | ||
sound | ||||
∙Wiring to the projector is not correct. | ∙Connect the cable correctly. | P.9, 28 | ||
| ||||
|
|
|
| |
Only picture is | ∙Wiring to the projector is not correct. | ∙Connect the cable correctly. | P.9, 28 | |
∙The volume is set to minimum. | ∙Press the VOL button or press the MENU button | P.10, 17 | ||
displayed with no | ||||
| and adjust the volume. |
| ||
sound |
| P.8, 10 | ||
∙The unit enters the mute mode. | ∙Press the MUTE button. | |||
| ||||
Only sound is | ∙Wiring the projector is not correct. | ∙Connect the cable correctly. | P.9, 28 | |
∙The brightness is set fully to the dark | ∙Press the MENU button and select BRIGHT and | P.17 | ||
heard without a | ||||
side. | press the button. |
| ||
picture | P.13 | |||
∙Lens cap is attached. | ∙Remove the lens cap. | |||
| ||||
|
|
|
| |
Color is weak and | The color and tint have been adjusted | Adjust the color and tint correctly. | P.17 | |
tint is incorrect | incorrectly. |
|
| |
Picture is dark | ∙The brightness and contrast has been | ∙Adjust the brightness and contrast correctly. | P.17 | |
adjusted incorrectly. |
| P.29 | ||
| ∙The lamp has not been adjusted. | ∙Replace the lamp with a new one. | ||
|
|
|
| |
Picture is not clear | Focus or H.PHASE is not matched. | Adjust the focus or H.PHASE | P.13, 17 | |
|
|
|
| |
LAMP indicator | Trouble with the lamp. | Turn off the power and leave for 45 minutes ; | P.32 | |
lights red. | then turn the power on again. | |||
|
| |||
Remote control | ∙Cable was connected after the power | ∙Be sure to perform procedure in the following order: |
| |
was turned on. | (1)Connect cable. (2)Turn on projector. (3)Turn PC on. |
| ||
mouse cannot be | P.23 | |||
∙RGB signal not selected. | ∙Input RGB signal and select and display input | |||
operated. |
| |||
| source. |
| ||
|
|
|
A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.
ENGLISH
33
