Hitachi DV-PF35U Preparation for Use English, Turn on the unit for the first time, Clock Set Up

Preparation for Use

English

Setup

Turn on the unit for the first time

press VCR first.

* Refer to page 11 to switch between the VCR/DVD modes.

1

Turn on the TV and set it to channel 3.

•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section on page 7.

2	LANGUAGE SELECT
	B ENGLISH	[ON]
	FRANCAIS
	ESPAÑOL
	or
	To select the desired language
	To decide
3		CH 01

AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the VCR/DVD’s ANT IN jack?

YES

Yes Press MENU

to exit

•Refer to “Hint for Cable Box or

Satellite Box” section on page 7. NO

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using SKIP/CH (i/Kor j/L).

•If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press Cursor B once again.

Hint

•Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

To Add or Delete Channels

1)Press MENU until the main menu appears.

2)Select “CHANNEL SET UP” by pressing Cursor K or L. Then, press Cursor B.

3)Select “MANUAL SET UP” by pressing Cursor K or L. Then, press Cursor B.

4)Enter the desired channel number by pressing Cursor K or L.

5)Add or Delete it from memory by pressing Cursor { or B. so that “ADD” or “DELETE” flashes on the TV screen accordingly.

6)Exit the preset mode by pressing CLEAR/C.RESET.

To Preset the Channel Again

1)Press MENU until the main menu appears.

2)Select “CHANNEL SET UP” by pressing Cursor K or L. Then, press Cursor B.

3)Select “AUTO SET UP” by pressing Cursor K or L. Then, press Cursor B. After scanning, the tuner stops on the lowest memorized channel.

To Change the On-Screen Language

1)Press MENU until the main menu appears.

2)Select “LANGUAGE SELECT” by pressing Cursor K or L. Then, press Cursor B.

3)Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by pressing Cursor K or

L. Then, press CLEAR/C.RESET.

Hint

•If you accidentally select Spanish or French but need English: Press MENU and choose SELEC. IDIOMA, or SELECTION LANGUE. Press

Cursor B, and select ENGLISH. Finally, press CLEAR/C.RESET.

Clock Set Up

press VCR first.

2		CLOCK SET
or	MONTH DAY		YEAR
	0 3	/ – –	– – – –
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current month
	To decide
3		CLOCK SET
or	MONTH DAY		YEAR
	0 3	/ 1 5	– – – –
	HOUR MINUTE		AM/PM
	– –	: – –	– –

Select the current day

To decide

4		CLOCK SET
or	MONTH DAY		YEAR
	0 3	/ 1 5	2 0 0 5
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current year
	To decide

5		CLOCK SET
or	MONTH DAY		YEAR
	0 3	/ 1 5 TUE	2 0 0 5
	HOUR MINUTE		AM/PM
	0 5	: – –	– –
	Select the current hour
	To decide
6		CLOCK SET
or	MONTH DAY		YEAR
	0 3	/ 1 5 TUE	2 0 0 5
	HOUR MINUTE		AM/PM
	0 5	: 4 0	– –

Select the current minute

To decide

7		CLOCK SET
	MONTH DAY		YEAR
	0 3	/ 1 5 TUE	2 0 0 5
or	HOUR MINUTE		AM/PM
	0 5	: 4 0	P M AM
			BPM

To Select a Channel

You can select a channel by directly entering channel using

the Number buttons on the remote

control.

Notes for using the Number buttons:

• When selecting cable channels which

are higher than 99, enter channel

numbers as a three-digit number.(For

example: 117, press 1,1,7)

• You must precede single-digit channel

1 MENU

or

-MENU-

TIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

BCLOCK SET LANGUAGE SELECT AUDIO OUT

TV STEREO [ON]

SAP

•If the clock is not set, the CLOCK SET screen appears when you press MENU. In this case, go to step [2].

Select “AM” or “PM”

8To exit the CLOCK SET screen.

CLEAR

or C.RESET

Hint

• To go back one step, press Cursor s

(during the steps [2] to [7].)

• Your clock setting will be lost if either there

numbers with 0 (For example: 02, 03,

04 and so on).

To decide

is a power failure or this unit has been

unplugged for more than 30 seconds.

– 12 – EN