Adjusting the Speaker Volume Level

This unit is set to the standard level before shipping from the factory. You may not need adjustment.

But, depending on the size of the room and the placement of the speakers, you may need a fine adjustment.

In this case, follow the steps below. Please use the remote control at the listening point.

1.Press [SOURCE] to select the desired function.

2.Press [SURROUND] repeatedly to select the desired surround mode (“DOLBY PL”, “DOLBY 3”, “THEATER” or “HALL”). (See “Selecting the Surround Mode” on Page E16.)

3.Press [TEST TONE] on the remote control. “TTONE” appears and “FL” blinks.

The test tone will be heard from each speaker sequentially as follows.

Surround mode

FL display (Speaker)

 

 

DOLBY PL

FL (Front left speaker)

THEATHER

C (Center speaker)

HALL

FR (Front right speaker)

 

RS (Surround right speaker)

 

LS (Surround left speaker)

 

 

DOLBY 3

FL (Front left speaker)

 

C (Center speaker)

 

FR (Front right speaker)

 

 

b

 

 

 

 

 

E T

P

 

M

 

 

 

 

 

 

 

 

a

 

 

 

 

 

U

 

 

 

U

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TRIM

SHIFT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLEAR

SHIFT

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

T

 

 

 

 

 

 

 

 

 

 

 

TRIM

 

REV

 

 

 

P

 

 

 

 

 

 

L

E

 

 

FWD

 

 

 

 

 

 

O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLOW

 

 

 

M

 

 

 

 

IT

 

 

 

 

SLOW

 

 

 

 

 

 

 

 

E

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

U

 

U

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

-

 

P

 

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

+

 

T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

U

 

R

 

 

 

 

 

 

 

 

 

 

X

 

 

E

 

 

 

E

 

 

 

 

 

 

 

E

 

 

N

 

 

 

NE

 

 

 

V

 

P

 

 

 

 

N

 

 

U

 

 

 

 

 

 

 

 

 

 

AUS

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E/STEP

 

 

 

 

 

 

 

 

 

 

 

1 2 3

ANGLE A.REPLAY ZOOM

4 5 6

AUDIO SLEEP

 

7

8

9

 

 

TIMER

ADJUST

SET/CLEAR

 

 

0

 

+10

 

 

CLOCK

 

 

 

 

TU/BAND

 

SOURCE

1

 

 

 

 

 

PRESET

FM MODE

TEST TONE

3, 5

 

 

 

 

2

SURROUND

BASS

SOUND

TEST TONE

 

 

 

SURROUND

MUTE

VOLUME

 

 

 

 

 

 

 

 

 

 

4, 6

 

 

 

 

DV-RM522

 

 

VOLUME

4.Press [VOLUME] o or p until the test tone is at a comfortable level.

If the test tone level is not the same from each speaker, you may need fine adjustment of the volume level. Please follow the steps as below.

Note:

If no adjustments are made, the original display returns after approximately 15 seconds.

1)Press [TEST TONE] to turn the test tone off.

2)Press [SURROUND] to select the desired surround mode.

3)Press [TRIM] while holding [SHIFT] down. “FNTL 0” appears.

4)Press [ENTER] repeatedly to select the speaker.

FL display (Speaker)

FNTL (Front left speaker)

CENT (Center speaker)

FNTR (Front right speaker)

SURR (Surround right speaker)

SURL (Surround left speaker)

SUBW (Subwoofer)

5)Press [a] or [b] to adjust the volume level. FNTL/FNTR: “0” ~ “-10” appears. CENT/SURR/SURL/SUBW: “+10” ~ “-10” appears.

6)Press [ENTER].

7)Repeat step 4) to 6) for another speaker, if necessary.

8)Press [TRIM] again while holding [SHIFT] down to turn it off.

5.Press [TEST TONE] to turn the test tone off. “TTONE” disappears.

6.Press [VOLUME] o or p to adjust the volume as desired.

Notes:

There is no Dolby Surround effect when monaural program material is used.

When receiving weak FM broadcasts, switch the Dolby Pro Logic off. The sound quality may improve.

When headphones are connected while any of the surround modes are selected, the surround mode is switched off automatically. The SURROUND button does not function while headphones are connected.

Trimming can be set at each function respectively.

-E17-

Page 18
Image 18
Hitachi DV-S522U instruction manual Adjusting the Speaker Volume Level, Trim, Enter, Test Tone