Result codes Procedure | Hitachi HV-F22F, HV-F31F specs

(9) AUTO SETUP STATE

(CSR: F200 01004 h) (read only)

Resulting data of One Push Auto White Balance (AWB), One push Auto BLACK Balance (ABB), One push Auto Shading (ASC) and One Push (Color DTL Auto Setup) are shown.

-DATA-

000xyyzzh	x: 0- NON, 1- WHITE, 2- BLACK, 3- SHAD, 4- DTL
	yy: Progress condition 00h- 0% , FF- 100%
	zz: Result	00h	- Normal end
		FFh	- under adjustment (busy)
		11h to 26h - Error end

Result codes: Procedure

11h: Turn off the color bar

12h: (WHITE BALANCE) change to Manual

13h: Increase the intensity of illumination, turn lens iris to ward open direction, or increase the gain to provide a proper video level.

14h: Decrease the intensity of illumination, turn lens iris toward closed direction, or decrease the gain to provide a proper video level.

15h: The color temperature is too high, making it impossible to reach the optimum value in adjustment. (If there is no problem in practical application, use the camera under the current condition.)

Page 48

Image 48

Hitachi HV-F22F, HV-F31F operation manual Result codes Procedure, CSR F200 01004 h read only

Contents

HV-F22F Cleaning AccessoriesRead Instructions Retain Instructions Power Sources Power-Cord ProtectionGrounding or Polarization Lightning Damage Requiring Service Replacement PartsSafety Check Servicing Alle Anweisungen lesen Die Anweisungen aufbewahrenWarnungen beachten Anweisungen befolgen Stromversorgung Erdung oder PolarisierungNetzkabelschutz Blitzschlag Eindringen von Fremdkörpern und Flüssigkeit Entflammbare und explosive SubstanzenStarke stöße oder Vibrationen Wartung Ersatzteile SicherheitsprüfungAnbringung an der Wand oder an der Decke 24. Wärme Accessoires Lire les instructionsConserver ces instructions Tenir compte des avertissements Sources d’allmentation Mise á la terre ou polarisationProtection du cordon d’alimentation Foudre 19. Réparations 21. Piéces de rechange 22. Vérificaton de sécurité Montage au mur ou au plafondChaleur Important Notice Table of contents Standard composition CD-ROM CPU Features Overview Important safety notes Operating considerations Power supplyConnectors Installation and storage sites CCD properties TransportationSmear and blooming Fixed pattern noise Moire Ghosting System example IEEE1394 connector see Note Section names and functions Connector IEEE1394 connectorDC IN/SYNC connector HR10A-10R-12PB01 Lens Selecting a lens Camera mounting Control and Status register CSR Function description Setting value 820xx0yy h Xx 00h to FFh B gain Iidc Standard CSRSharpnesscsr F0F0 0808 h Setting value 82000xxx h Xxx 000h to 0C0h 1dB ≒ 010h Setting value 80000000 hSwitches off shutter operation Sets electronic shutter speed Cause of shutter speed ≦ 1 / Offspeed Cause of shutter speed 1 / Offspeed Setting value 820000xx h Xx 00h to FFh standard80 h Color saturation is adjustedSetting value 820000xx h Video level decreases toward 00h and increases toward FFh Setting value 80000000h Gamma correction is set to OFFCSR F0F0-0818 h CSR F0F0 0830 h See trigger operation details and timing chart Select channel carried out memory backupLoading memory channel designating data Masking R Saturation CSR F200 0024 h Manual adjustment Masking Y Saturation CSR F200 0028 h Manual adjustmentMasking G Saturaton CSR F200 002C h Manual adjustment Maskingcsr F200 0020 h Setting value 820000xx h Xx 00hto FFh standard 80 h CSR F200 0048 h Manual adjustment Masking B HUE CSR F200 004C h Manual adjustmentCSR F200 0050 h Manual adjustment Gamma Total Manual adjustment Mode selection One push ASC CSR F200-0098 h Black balance is adjusted Sharpness signal width can be setSetting value 8200000x h LOW, 1- MID, 2- High Image quality related CSR Manual adjustment Setting value 820000xx h Xx 00h toFFh Setting value 820000xx h Xx 00h to FFhSharpness Level Dependent CSR F200 00B4 h Sharpness Clisp CSR F200 00B8 h Setting value 82000xyy h Setting value 820xx0yy h Sharpness Color DTL Ch2 CSR F200 00C8 h Sharpness Color DTL Ch2 WIDTH/LEVEL CSR F200 00CC hKnee CSR F200 00D4 h Setting value 8200000x h SLOW, 1- MID, 2- Fast Improve S/N by digital noise reductionImage level related CSR AGC and AES response speed Setting value 820xx0yy h Xx Line 1 ON/OFF data Yy Line 2 ON/OFF bit map data E Gate line7-8 CSR F200 0088 h Manual adjustment Gate line1-2 to line7-8 setting examples CSR related to other functions CSR F200 0018 hBAR CSR F200 00DC h Nega CSR F200 00E0 h Horizontal phase can be adjusted See setting range on page 42 External sync timingSets pixel concealment on/off Each type of indicator is displayed Setting value 80000000 h Setting value 8200000x h Result codes Procedure CSR F200 01004 h read onlyPage Specification HV-F31F HV-F22F Auto Exposure Input/Output Signals IEEE1394 interface IEEE1394 connector 1360 1280 DC IN/SYNC input and output DC IN/SYNC connector External trigger input Trig in connector Trigger operation and timing chart HV-F31F Delay 1250us Data transfer Data transfer Start 2.1ms HV-F22F 5FPS Delay 1250us Data transfer Data transfer Start 3.0ms External sync timing Dimensions