English

BCL1415

BCL1815

BSL1415

BSL1815X

BCL1430

EBM1830

BSL1415X

BSL1830

 

 

BSL1430

 

2.Charger

￿UC18YRL (Charging voltage: 7.2 V – 18 V)

￿UC18YRSL (Charging voltage: 7.2 V – 18 V)

UC18YRLUC18YRSL

Optional accessories are subject to change without notice.

APPLICATIONS

￿Light-duty vacuuming of dry surfaces

￿Light-duty vacuuming of damp or wet surfaces

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch (2 pcs.) to remove the battery (see Figs. 1, 2, 4 and 5).

CAUTION

Never short-circuit the battery.

2.Battery installation

Insert the battery while observing its polarities (see Figs. 1, 2, 4 and 5).

CHARGING

For rechargeable batteries, please charge in according to the handling instructions of the charger which you are using. (Figs. 3 and 6)

PRIOR TO OPERATION

1.Setting up and checking the work environment Check if the work environment is suitable by following the precautions.

2.Mounting and dismounting the water guard and filter

Before using the appliance, check that the filter is securely mounted. (Figs. 7 and 8)

9

(1)Mounting

1 Match the outside diameter of the filter to the

inside diameter of the water guard and insert as far as the filter ring will go. (Fig. 7)

2Match the shape of the water guard (with the filter attached) to the shape of the hole in the dust case and insert as far as it will go (6 points). (Fig. 8)

(2)Dismounting

To dismount the water guard and the filter, follow the above procedures in reverse.

3.Attaching and removing the suction opening

Insert the suction opening into the suction port of the appliance as required. (Fig. 10)

HOW TO USE THE CORDLESS CLEANER

CAUTION

￿To prevent accidents when installing or removing the rechargeable battery, make sure that the appliance is switched off.

￿Make sure that the rechargeable battery is properly installed.

If not properly installed, the battery may fall out,

causing injury.

1.Switch operation

Flip the switch towards you to start operation and back to stop operation. (Fig. 11)

2.Vacuuming water

Attach the squeegee nozzle as required. (Figs. 10 and

12)

CAUTION

￿The maximum line on the dust case indicates the maximum amount of water that can be vacuumed. Do not vacuum beyond this line. (Fig. 12)

￿Empty the water immediately after vacuuming.

￿Do not carry the appliance with water in the dust case.

3.Emptying the dust case

CAUTION

￿To prevent accidents, make sure the power is switched off and remove the rechargeable battery from the appliance.

￿Do not subject the dust case to strong impacts as this may cause deformation or damage.

￿Empty the dust case frequently and keep the appliance, filter, etc. clean. Failure to do so may reduce vacuuming efficiency or cause malfunction of

the motor or odor.

(1)Press the release button and remove the dust case. (Fig. 9)

(2)Hold the knob on the water guard (with the filter attached) to remove it from the dust case. (Fig. 8)

(3)Empty the dust case. (Fig. 13)

(4)Take hold of the knob on the filter and remove the filter from the water guard. (Fig. 7)

(5)Lightly tap the filter to remove all the dust. (Fig. 14)

(6)Fit the filter to the water guard. Match the outside diameter of the filter to the inside diameter of the water guard and insert as far as the filter ring will go. (Fig. 7)

(7)Match the shape of the water guard (with the filter attached) to the shape of the hole in the dust case and insert as far as it will go (6 points). (Fig. 8)

(8)Insert the projecting part of the appliance into the hole in the dust case and fit the dust case to the appliance. (Fig. 9)