USING DIFFERENT NOZZLES
Variable nozzle (with pressure adjustor) (Fig. 11)
The variable nozzle (with pressure adjustor) can be used to alternation between “Jet” and “Spray” and between “High Pressure” and “Low Pressure”.
Rotate the end on the nozzle clockwise for “Jet”, and
Also, rotate the pressure adjuster clockwise for “Low Pressure”, and
• Jet washer
A water jet is discharged in a direct line to remove stubborn mud and other dirt from agricultural machinery, etc.
• Spray washer
The water is discharged in a wide fan for cleaning walls, motorbikes and automobiles, etc.
The entire nozzle can be rotated by approximately 90 degrees to change the shape of the spray between horizontal and vertical.
NOTE
The pressure adjuster will also be rotated when alternating between “Jet” and “Spray”, so readjust this to the required setting after making the adjustment.
Set the spray adjustment to “Jet” first of all, and then gradually move it to the “Spray” position while pulling the trigger.
Note that there is a chance of the water being sprayed horizontally over a wide area if this is rotated fully to the “Spray” position.
Note that the nozzle may be damaged if it is forced to move past the stop position when alternating between “Jet” and “Spray”.
Turbo nozzle
The turbo nozzle rotates as it sprays
NOTE
The turbo nozzle only discharges powerful jets of water when set at the “Jet” mode.
Avoid using this on items that are easily broken or for which coatings are easily peeled.
USING THE DETERGENT BOTTLE (Fig. 12)
Sprays water mixed with detergent.
Uses neutral detergents available on the open market.
WARNING
Do not use acidic or alkali detergents. Use only neutral detergents available on the open market.
Using detergents other than neutral detergents or chemical agents may result in accidents or malfunctions.
NOTE
Check to make sure that the water feed pipe is firmly connected to the washer.
The detergent will not be mixed with the spray otherwise. ï Remove the cap from the detergent bottle and pour the
detergent into it.
î Make sure the filter on the tip of the detergent bottle’s water feed pipe is inserted into the liquid and then tighten the cap firmly.
NOTE
Only the “Low Pressure” setting can be used for variable nozzles (with pressure adjustors) when using the detergent bottle.
English
The detergent will not be sprayed if the “High Pressure” setting on variable nozzles (with pressure adjustors) or turbo nozzles are used.
í Set the adjustor to “Low Pressure” when using variable nozzles (with pressure adjustors.)
ì Water containing the detergent will be sprayed at low pressure when the trigger on the trigger gun is pulled.
Cleaning the detergent bottle (Figs. 13 and 14)
ïRemove the detergent bottle’s water feed pipe from the washer.
Push the detergent bottle from the bottom and withdraw it from the top.
Wash the detergent bottle, water feed pipe and filter with water from the faucet.
When reattaching the bottle, hold it as shown in Fig. 14, and then push the protrusion on the bottom in as far as it will go.
Insert the water feed pipe into the washer and tighten the
cap while making sure dust or dirt does not enter.îíìë
USING THE STRAINER HOSE SET (sold separately)
The
The maximum height of suction (lifting range) is approximately 0.5 m.
Attach this correctly in accordance with conditions.
Í«½¬±²¸»·¹¸¬©¸»²¬¸»¸»·¹¸¬±º¬¸»©¿¬»®º»»¼±«¬´»¬ |
·- ´±©»®¬¸¿²¬¸»³¿¨·³«³¸»·¹¸¬±º¬¸» |
Ú®±³ ¬¸» ³¿¨·³«³ ¸»·¹¸¬±º¬¸» |
Ó¿¨·³«³ ¸»·¹¸¬±º |
¬¸» |
Water surface |
Water |
feed inlet |
Í«½¬·±² ¸»·¹¸¬©¸»² ¬¸» ¸»·¹¸¬±º¬¸» ©¿¬»®º»»¼ |
±«¬´»¬·- ¬¸» |
±º¬¸»©¿¬»®ò |
É¿¬»®º»»¼·²´»¬ |
ø³¿¨·³«³ ¸»·¹¸¬±º |
¬¸» |
Water surface
19