ASSEMBLY
WARNING:
If any parts are damaged or missing do not operate this prod- uct until the parts are replaced. Use of this product with dam- aged or missing parts could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories not recommended for use with this product. Any such altera- tion or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
To remove, depress the latch on top of the fitting and remove the hose from the spout.
n The high pressure hose has a metal connection and slides into the opening at the top of the trigger handle.
Grasp the hose lock and pull outward to clear the way for the high pressure hose to be inserted.
Insert the high pressure hose all the way into the hole.
Push the hose lock fully back into the handle to hold the high pressure hose in place.
connectingthe garden hose
See Figures 8 - 10.
WARNING:
Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.
installing the wheels
See Figure 4.
n Locate the axles, hitch pins, washers, and wheels. n Slide the axle through the hole in the center of the wheel.
n Lift the machine and slide the axle into the wheel mounting hole in the machine base as shown.
n Slide the washer on the axle, then push the hitch pin into the hole on the end of the axle to secure the wheel assembly.
NOTE: The hitch pin should be pushed into the axle until the center of the pin rests on top of the axle.
n Repeat with the second wheel.
attaching the handle assembly
See Figure 5.
n Orient the handle assembly as shown.
nDepress the button on the handle assembly and insert into the holes on the pressure washer. Press down on the handle assembly until the button on the handle clicks into place.
nLower both collars on the handle and rotate clockwise until secure.
assembling the spray wand
See Figure 6.
n Push the two ends of the spray wand together so that the holes inside each end are aligned.
nLower the locking collar and rotate counterclockwise until you hear the clicking sound, which indicates the wand is securely tightened.
nPlace the assembled spray wand in the spray wand holder with the notched area resting on the pressure washer handle.
attaching the high pressure and low pressure hoses to the trigger handle
See Figure 7.
Caution:
Always observe all local regulations when connnecting hoses to the water main. Some areas have restrictions against connecting directly to public drinking water sup- ply to prevent the feedback of chemicals into the drinking water supply. Direct connection through a receiver tank or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use hot water or water from pools, lakes, etc. Before connecting the garden hose:
nUncoil the garden hose.
NOTE: There must be a minimum of 10 feet of unrestricted garden hose between the water intake and the garden hose faucet or shut off valve (such as a “Y” shut off connector).
nRun water through the garden hose for 30 seconds to clean any debris from the hose.
To connect the garden hose to the machine through
nLoosen bracket screws and remove bracket.
nRotate the
nDisassemble injector as described in the Using the Deter- gent Injector section of the manual. Ensure that the
nInspect the filter screen in the water intake.
If the screen is damaged, do not use the machine until the screen has been replaced.
If the screen is dirty, clean it before connecting the garden hose to the machine.
nReassemble injector, return it to unit, and replace bracket.
nWith the garden hose faucet turned completely off, attach the end of the garden hose to the
To connect the garden hose directly to the machine:
nRemove the
nInspect the filter screen in the water intake. Clean or replace as needed.
nWith the garden hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by hand.
nThe low pressure hose is the clear tube with the plastic fitting and goes on the spout at the bottom of the trigger handle.
Grasp the plastic fitting and slide onto the spout until it clicks into place.
Page 10 — English