Honda Power Equipment FG100 34

TRANSPORTING

Before Loading

Always turn the engine switch to the OFF position.

Make sure the fuel cap is securely tightened.

Install the wheels to provide added stability when

transporting (see page 12).

If the engine has been running, allow it tocool for at

least 15 minutes before loading the tiller on the

transport vehicle. A hot engine andexhaust system

can burn you and can ignite some materials.

Loading

If necessary, loosen the handlebar knobs so that

the tiller upper handlebar can be collapsed. Be

careful that the throttle cable and engine switch

wire are not pinched or bent when collapsing the

upper handlebar.

Secure the tiller by tying around the lower

handlebars just in front and back of the engine as

shown.

STORAGE

Proper storage preparation is essential for keeping

your tiller troublefree and looking good. The

following steps will help to keep rust and corrosion

from impairing your tiller’s function and

appearance, and will make the engine easier to

start when you use the tiller again.

Cleaning

Wash the tiller, including the area around the tiller

tines.

Wash the engine by hand, and be careful to

prevent water from entering the air cleaner.

NOTICE

Using a garden hose or pressure washing

equipment can force water into the air cleaner.

Water in the air cleaner will soak the filter and can

enter the carburetor or engine, causing damage.

Water on a hot engine can cause damage. If the

engine has been running, allow it to cool for at least

1/2 hour before washing.

If using a garden hose or pressure washing

equipment to clean the tiller, be careful to avoid

getting water into controls and cables, or anywhere

near the engine air cleaner or muffler opening.

After washing the tiller, wipe dry all accessible

surfaces.

Start the engine outdoors, and let it run until it

reaches normal operating temperature to evaporate

any water remaining on the engine.

Stop the engine and allow it to cool.

After the tiller is clean and dry, touch up any

damaged paint, and coat other areas that may rust

with a light film of oil. Lubricate the throttle cable

core with a silicone spray lubricant.

HANDLEBAR

KNOBS

THROTTLE

CABLE & ENGINE

SWITCH WIRE

UPPER

HANDLEBARS

TIE DOWN

HERE

TIE

DOWN

HERE

TRANSPORTING/STORAGE

34 FG100 TILLER

Contents

Main BWARNING: B INTRODUCTION NOTICE Distributors Limited Warranty (Page 40) A FEW WORDS ABOUT SAFETY B DANGER B WARNING B CAUTION CONTENTS IMPORTANT SAFETY INFORMATION 4 ATTACHMENTS AND MODIFICATIONS Accessories, Replacement & Parts and Appeal Warranty (Page 41) IMPORTANT MESSAGE TO EMPLOYERS IMPORTANT MESSAGE TO PARENTS SAFETY LABEL LOCATIONS DANGER 6 COMPONENT IDENTIFICATION FG100 TILLER 7 DESCRIPTION OF CONTROLS 8 Throttle Lever Engine Switch Choke Lever Priming Bulb Transport Wheels Carrying Handle Recoil Starter Grip Drag Bar Tine Spacers (included with tiller) 10 Knowledge Physical and Mental Readiness Protective Clothing Hand and Body Protection BEFORE OPERATION SAFETY PRECAUTIONS 12 IMPORTANT SAFETY INFORMATION BEFORE OPERATION Moving The Tiller Drag Bar Installation Starting The Engine Stopping The Engine TILLER OPERATION 14 Handling Tips Tilling In Rocky Soil D Narrow Cultivating 16 THE IMPORTANCE OF MAINTENANCE MAINTENANCE SAFETY Safety Precautions MAINTENANCE SCHEDULE 18 ENGINE MAINTENANCE Engine Oil Level Check Running the engine with too little or too much oil can cause engine damage. Engine Oil Change Engine Oil Recommendations 20 Air Filter Inspection UP Air Filter Cleaning Air Filter Cleaning Spark Plug Service 22 Incorrect spark plugs can cause engine damage. Spark Arrester Service MAINTENANCE & ADJUSTMENTS Cooling Fin Inspection Throttle Cable Inspection Throttle Cable Adjustment Carburetor Adjustment FUEL SYSTEM Refueling . Fuel Recommendations Running the engine with persistent spark knock or pinging can cause engine damage. Distributors Limited Warranty 26 Fuel Filter and Fuel Tank Cleaning TRANSMISSION LUBRICATION THE IMPORTANCE OF PROPER ASSEMBLY 28 IMPORTANT SAFETY PRECAUTIONS UNPACKING 7 8 9 12 23 24 25 16 17 18 19 20 21 22 10 11 30 Page 32 Running the engine with too little or too much oil can cause engine damage. CONTROLS TILLER SAFETY OPERATION BEFORE OPERATION TRANSPORTING 34 Before Loading Loading STORAGE Cleaning Fuel Distributors Limited Warranty Adding Fuel Stabilizer To Extend Fuel Storage Life Draining the Fuel Tank and Carburetor Engine Oil 36 REMOVAL FROM STORAGE BEFORE OPERATION STARTING PROBLEMS ENGINE OPERATING PROBLEMS TAKING CARE OF UNEXPECTED PROBLEMS ENGINE 38 * Actual fuel consumption will vary depending on engine load conditions. TILLER SPECIFICATIONS SERIAL NUMBER LOCATIONS CONSUMER INFORMATION Find an Authorized Honda Servicing Dealer in Your Area Honda Publications Shop Manual 40 Distributors Limited Warranty To Qualify for this Warranty: What American Honda will Repair or Replace Under Warranty: Noncommercial/Nonrental Commercial/Rental Accessories, Replacement Parts, and Apparel Warranty To Qualify for this Warranty: Exclusions: Emission Control System Warranty 42 Your Warranty Rights And Obligations: California Other States All States Manufacturers Warranty Coverage: Exclusions: Emission Control System Warranty Parts WARRANTY SERVICE INFORMATION 44 OXYGENATED FUELS CARBURETOR MODIFICATIONS FOR HIGH ALTITUDE OPERATION EMISSION CONTROL SYSTEM INFORMATION 46 Source of Emissions The U.S and California Clean Air Acts Tampering and Altering REPLACEMENT PARTS A B C D INDEX QUICK REFERENCE Maintenance Tuneup * Resistor plugs reduce the interference with radio and television reception.