Manuals / Brands / Computer Equipment / Scanner / Honeywell / Computer Equipment / Scanner

Honeywell 7580g ACK/NAK, XON/XOFF, Scanner-BiopticPacket Mode, ACK/NAK On, ACK/NAK On, XON/XOFF On, XON/XOFF On, ACK/NAK Off, XON/XOFF Off, * ACK/NAK Off, * XON/XOFF Off

1 202

Download 202 pages, 3.74 Mb

XON/XOFF

Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scanner, data transmission stops. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off

when XOFF was sent. Default = XON/XOFF Off.

XON/XOFF On

* XON/XOFF OffACK/NAK

After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK

Off.

ACK/NAK On* ACK/NAK Off

Scanner to Bioptic Communication

The following settings are used to set up communication between Honeywell scanners and bioptic scanners.

Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner. See "RS232 Modifiers" on page 2-18,and RS232 Timeout on page 2-20for further information.

Scanner-Bioptic Packet Mode

Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default = Packet

Mode Off.

* Packet Mode Off

Packet Mode On

2 - 21

Contents

Page Page FCC Part 15 Subpart B Class B UL Statement Industry Canada ICES-003 Conformité à la règlementation canadienne C-ULStatement Honeywell Scanning & Mobility Product Environmental Information C-TickStatement LED Safety Statement CB Scheme Page Page Table of Contents Chapter 3 - Input/Output Settings Centering High Priority Symbology Low Priority Symbology Output Sequence Editor Chapter 4 - Data Editing Prefix/Suffix Overview Suffix Selections Intercharacter Delay Chapter 5 - Data Formatting Chapter 6 - Symbologies Chapter 7 - EAS Settings Chapter 8 - Imaging Commands Chapter 9 - Interface Keys Chapter 10 - Utilities Chapter 11 - Serial Programming Commands Chapter 12 - Product Specifications Chapter 13 - Maintenance Chapter 14 - Customer Support Appendix A - Reference Charts Sample Symbols Programming Chart Page Getting Started Keyboard Wedge Connection: Connecting with RS232 Serial Port RS232 Serial Port Connecting with RS485 RS485 Connection: Connecting with EAS USB Interface with EAS RS232 Interface with EAS Set Custom Defaults Save Save Custom Defaults Set Custom Defaults Save Custom Defaults Activate Custom Defaults Activate Custom Defaults Programming the Interface IBM Port 5B Interface IBM Port 9B HHBCR-1Interface IBM Port 17 Interface RS485 Packet Mode * Packet Mode Off Packet Mode On RS485 Packet Length Packet Length USB HID Bar Code Scanner USB Serial CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On Symbology Prefix Page Keyboard Countries Keyboard Countries (Continued) Page Page Page Page Page Regular Caps Lock Caps Lock Shift Lock Shift Lock Automatic Caps Lock Autocaps via NumLock Control + X (Control + ASCII) Mode On: Windows Mode Prefix/Suffix Off: Turbo Mode: Numeric Keypad Mode: Automatic Direct Connect Mode: RS232 Baud Rate RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits Stop Bits Parity RS232 Receiver Time-Out RS232 Receiver Time-Out RS232 Handshaking Flow Control, No Timeout: Two-Direction XON/XOFF XON/XOFF On XON/XOFF Off * XON/XOFF Off ACK/NAK Scanner-BiopticACK/NAK Mode Bioptic ACK/Nak On * Bioptic ACK/NAK Off Bioptic ACK/NAK On Scanner-BiopticACK/NAK Timeout Input/Output Settings Beeper – Good Read Off Beeper - Good Read Off * Beeper - Good Read On Beeper Volume – Good Read Beeper Pitch – Error Beeper Duration – Good Read LED – Good Read Number of Beeps – Good Read Number of Beeps – Error Good Read Delay User-SpecifiedGood Read Delay Normal LED Illumination - Manual Trigger Read Time-Out Read Time-Out Read Time-Out * Presentation Mode Presentation LED Behavior after Decode LEDs Off Presentation Sensitivity Sensitivity Presentation Centering Presentation Centering On * Presentation Centering Off Top of Presentation Centering Window Bottom of Presentation Left of Presentation Centering Right of Presentation Centering *CodeGate Off Out-of-Stand CodeGate On Streaming Presentation – Mobile Phone Presentation – Mobile Phone Hand Held Scanning - Mobile Phone Streaming Presentation Long (1000 ms) Extra Long (2000 ms) User-SpecifiedReread Delay Lights On Lights Off User-SpecifiedAimer Delay Delay Duration * Interlaced Interlaced *Off *Enhanced Object Detection Centering On Top of Centering Window, Bottom of Centering Window, Left Right of Centering Window Centering On * Centering Off Top of Centering Window Bottom of Centering Window Left of Centering Window Right of Centering Window High Priority Symbology Low Priority Symbology Preferred Symbology Time-out Preferred Symbology Default To Add an Output Sequence Enter Sequence 2.Code I.D 3.Length 4.Character Match Sequences Partial Sequence Discard Partial Sequence Transmit Partial Sequence * Discard Partial Sequence On/Not Required Required Video Reverse Off Video Reverse Only Video Reverse and Standard Bar Codes Video Reverse Only Video Reverse Off Video Reverse and Standard Bar Codes Video Reverse Only Video Reverse and Standard Bar Codes Page Data Editing Example: Add a Tab Suffix to All Symbologies Step 1. Scan Add Suffix To Clear One or All Prefixes or Suffixes Clear One Prefix (Suffix) Clear All Prefixes (Suffixes) Intercharacter Delay Intercharacter Delay User Specified Intercharacter Delay Delay Length Character to Trigger Delay Interfunction Delay Interfunction Delay Intermessage Delay Intermessage Delay Data Formatting Step 5. Length Step 6. Editor Commands Enter Data Format Discard Clear One Data Format Send all characters Send a number of characters Send all characters up to a particular character Send all characters up to a string Send all but the last characters Insert a character multiple times Insert a string Insert symbology name Insert bar code length Insert key strokes Move the cursor forward a number of characters Move the cursor backward a number of characters Move the cursor to the beginning Move the cursor to the end Search forward for a character Search backward for a character Search forward for a string Search backward for a string Search forward for a non-matchingcharacter Search backward for a non-matchingcharacter Suppress characters Stop suppressing characters Replace characters Stop replacing characters Compare characters Compare string Check for a number Check for non-numericcharacter Insert a delay Discard Data Keep Prefix/Suffix Data Formatter On Not Required Data Format Non-MatchError Tone Data Format Non-Match Error Tone Off Error Single Scan Data Format Change Single Scan-Data Format Single Scan-Primary Page Symbologies <Default All Codabar Settings Codabar Concatenation Codabar Message Length < Default All Code 39 Settings Code 39 Message Length Code 39 Append Code 32 Pharmaceutical (PARAF) Full ASCII Full ASCII On * Full ASCII Off Code 39 Code Page Code 39 Code Page < Default All Interleaved 2 of 5 Settings < Default All NEC 2 of 5 Settings < Default All Code 93 Settings Code 93 Append Code 93 Code Page Code 93 Code Page <Default All Straight 2 of 5 Industrial Settings <Default All Straight 2 of 5 IATA Settings <Default All Matrix 2 of 5 Settings <Default All Code 11 Settings <Default All Code 128 Settings Code 128 Append Code 128 Code Page Code 128 Code Page <Default All GS1-128Settings <Default All Telepen Settings <Default All UPC-ASettings UPC-AAddenda UPC-AAddenda Required UPC-AAddenda Separator and Allow Concatenation Require Concatenation Allow Concatenation Require Concatenation <Default All UPC-ESettings UPC-E0Addenda Separator UPC-E0Check Digit UPC-E0Leading Zero UPC-E0Addenda <Default All EAN/JAN Settings EAN/JAN-13Check Digit EAN/JAN-13Addenda EAN/JAN-13Addenda Required EAN/JAN-13Addenda Separator ISBN Translate <Default All EAN/JAN-8Settings EAN/JAN-8Addenda Required EAN/JAN-8Addenda Separator <Default All MSI Settings MSI Message Length < Default All GS1 DataBar Omnidirectional Settings < Default All GS1 DataBar Limited Settings < Default All GS1 DataBar Expanded Settings <Default All Codablock A Settings <Default All Codablock F Settings < Default All PDF417 Settings < Default All MicroPDF417 Settings UPC/EAN Version UPC/EAN Version On UPC/EAN Version On * UPC/EAN Version Off GS1 Composite Code Message Length < Default All QR Code Settings QR Code Message Length QR Code Append QR Code Page QR Code Page < Default All Data Matrix Settings < Default All MaxiCode Settings < Default All Aztec Code Settings < Default All Han Xin Settings Single 2D Postal Codes: Combination 2D Postal Codes: Page Planet Code Check Digit Postnet Check Digit Australian Post Interpretation Bar Output Numeric N Table China Post (Hong Kong 2 of 5) On/Off China Post (Hong Kong 2 of 5) Message Length <Default All Korea Post Settings Korea Post Korea Post Message Length Korea Post Check Digit Page EAS Settings EAS Controller Settings SW2 SW1 Interlocked Continuous on Enable EAS Interlocked Duration Timeout EAS Interlocked Duration Timeout EAS Interlocked Duration Timeout Page Imaging Commands T - Wait for Trigger L - LED State E - Exposure G - Gain W - Target White Value D - Delta for Acceptance U - Update Tries % - Target Set Point Percentage IMGSNP;IMGSHP8F75K26U IMGSHP Modifiers A - Infinity Filter C - Compensation D - Pixel Depth E - Edge Sharpen F - File Format H - Histogram Stretch I - Invert Image IF- Noise Reduction IR - Image Rotate J - JPEG Image Quality K - Gamma Correction L, R, T, B, M - Image Cropping P - Protocol S - Pixel Ship U - Document Image Filter IMGSNP1P0L168W90%32D V - Blur Image W - Histogram Ship Image Size Compatibility Signature Capture Optimize Example: IMGBOX245w37h55y IMGBOX Modifiers A - Output Image Width B - Output Image Height H - Height of Signature Capture Area 37h R - Resolution of Signature Capture Area S - Bar Code Aspect Ratio W - Width of Signature Capture Area 245w X - Horizontal Bar Code Offset Y - Vertical Bar Code Offset Interface Keys IBM PC/AT and ASCII HEX Compatibles Apple Mac/iMac Utilities List Apps Scan Data Configure Imaging Remove Custom Defaults Activate Defaults Serial Programming Commands Data Field Usage Concatenation of Multiple Commands Responses ACK ENQ Product Default Settings Programming the Interface Page Page Page Input/Output Selections Page Page Prefix/Suffix Selections Data Formatter Selections Symbologies Page Page Page Page Page Page Postal Codes - 2D Postal Codes - Linear EAS Settings Imaging Default Commands Page Utilities Page Product Specifications Typical Performance Focus Standard Range (SR) Guaranteed Performance Keyboard Wedge Serial Output RS485 Output USB EAS EAS - USB EAS - Serial Output Maintenance Do not submerge the scanner in water. The scanner’s housing is not watertight Replacing a Genesis Interface Cable Cable Release Replacing a Genesis EAS Cable Is the power on? Is the aimer on The scanner won’t read your bar code at all Page Customer Support Page Reference Charts Possible modifiers 2D Symbologies Postal Symbologies Non-printable ASCII control Keyboard Control + ASCII (CTRL+X) Mode Windows Mode Control + X Mode On (KBDCAS2) Control + X Mode Off (KBDCAS0) Printable Characters Printable Characters (Continued) Extended ASCII Characters Alternate Extended PS2 Scan Code Extended ASCII Characters (Continued) Code Page Selection Method/Country Standard Keyboard Country Honeywell Code Page Option Page ISO / IEC 646 National Character Replacements 104 Key U.S. Style Keyboard 105 Key European Style Keyboard UPC-A Interleaved 2 of EAN-13 Codabar Code 2 of PDF417 Postnet Data Matrix QR Code Aztec Page Page Page Honeywell Scanning & Mobility