F111 (SERIES 1,2,3) IN CEILING MEDIA AIR CLEANER

Local, Federal and professional ventilation engineering standards and codes prescribe minimum ventilation rates to dilute air contamination in specific applications. The ventilation rates usually assume the injection of outdoor air measured as air exchange rate. The use of the F111 (series 1,2,3) air cleaner to comply with ventilation requirements is an acceptable alternative to ventilation with outdoor air. However, at least 20% of a specified ventilation rate or code must be derived from outdoor air. The F111 (series 1,2,3) air cleaner filtered and recirculated air can be the remaining 80%.

3.Place spent filter in a plastic trash bag and dispose of properly.

4.Inspect the motor brackets for loose fasteners and tighten as necessary.

5.Install the new filter noting the direction of airflow arrow.

6.For Series 1 and 2 only. Fasten the filter tabs. Be sure there is a snapping sound when they are fastened. The tabs are commercial Velcro and require more force to fasten.

7.For Series 3 only. Lock and secure the particle filter into place by closing both latches

SERVICE

CAUTION

Electrical Hazard.

Can cause personal injury or equipment damage. Turn off power before installing or servicing the air cleaner.

IMPORTANT

Be sure to change filters as recommended to prevent reduced airflow in the air cleaner.Stand on a stable platform when working with the air cleaner.

The useful life of the CPZ™ sorbent modules may vary from 4 to 24 months, depending on the application. In most applications, the sorbent media life ranges from 12 to 18 months. The particle filter life ranges from 6 to 24 months with 12 to 24 months as an average. The modules and filters need to be changed more frequently in facilities that operate 24 hours a day.

Prefilter

The disposable prefilter collects large dust particulates and lint- type airborne fibers. Check the filter every two weeks to determine the replacement frequency:

1.Slowly open the lid, supporting the lid so the filters do not fall out.

2.Remove the dirty prefilter.

3.Install the new prefilter in the air cleaner lid. Position the metal screen mesh so it is facing upward when the lid is closed.

4.Close and latch the lid.

Particle Filter

The particle filter collects particulates that pass through the prefilter. The filter life is typically from 1 to 2 years. There is decreased air quality and a pulsing sound when the filter is filled with contaminants. The filter must be replaced when the pulsing sound is noticed.

NOTE: The filter must be replaced. Washing, vacuuming or reverse air blasting does not clean it.

1.Slowly open lid, supporting it so the filters do not fall out.

2.Open the securing strips and with both hands. Slide the filter toward you.

IMPORTANT

Do not touch the pleated filter media. Handle only the filter frame to prevent damage to the filter media.

8.Close and latch the lid.

CPZ™ Adsorbent Module

The CPZ™ adsorbent module is used to collect gases, vapors, odors and volatile organic compounds (V.O.C.) from the air that passes through the air cleaner. Adsorbents collect and hold 25% to 50% of their weight in odorous gases and vapors. The impurities are collected until the adsorbents reach saturation. At saturation, the adsorbents emit a continuous strong pungent odor. If the air cleaner is turned off for 8 to 10 hours, there will a temporary odor when it is turned back on. If the odor persists for 30 minutes, it is time to replace the filters.

NOTE: When tobacco smoke is a contaminant, both the particle filter and the adsorbent filter will need to be serviced at the same time.

1.Slowly open the lid, supporting the lid so the filters do not fall out.

2.For Series 1 only. Support the adsorbent module with one hand and release the fastener.

3.For Series 2 and 3. Support the adsorbent module with one hand and turn open the catches.

4.Use two hands and slide the filter from the housing.

IMPORTANT

The module weighs about 26 lb (12 kg) and can be hard to handle.

5.Place the spent module in a plastic trash bag and dispose of properly.

6.Remove CPZ™ sorbent modules from their packaging and install.

7.For Series 1 only. Be sure the fastener tabs are facing downward and fasten them.

8.For Series 2 and 3 only. Be sure both catches are turned down and filter rests firmly on catches.

9.Install 1 startup-filter in each end of grill.

10.Close and latch the lid.

On initial startup, a small amount of dust can blow from the air cleaner. This is normal and stops a few minutes after startup. The startup-filters will catch all the dust. The startup-filters are placed in the two exit outlets on the grill. After running the unit for 5 minutes, turn off the unit. Remove and discard the two start-up filters.

68-0198-2 Revised 5-09

8

Page 7 Page 9
Page 8
Image 8
Honeywell F111 Series 3 specifications Service, Prefilter, Particle Filter, CPZ Adsorbent Module
Page 7 Page 9

F111 Series 3 specifications

The Honeywell F111 Series 3 is a notable aircraft in the realm of military aviation, primarily designed for ground attack and tactical strike missions. A derivative of the original F-111 Aardvark, the Series 3 variant exemplifies advanced engineering and technological innovations that enhance its combat capabilities.

One of the standout features of the F111 Series 3 is its unique variable-sweep wing design, which provides exceptional versatility in various flight conditions. This design allows the wings to adjust their angle during flight, optimizing performance for both high-speed intercepts and low-level tactical missions. As a result, the F111 can operate effectively at a wide range of speeds and altitudes, giving it a tactical edge over its peers.

Equipped with advanced avionics systems, the F111 Series 3 incorporates cutting-edge navigation and targeting technologies. Its onboard radar and electronic warfare systems enable it to detect and track enemy targets while remaining largely undetected. The aircraft can carry a diverse array of munitions, including precision-guided bombs and air-to-ground missiles, further enhancing its strike capabilities. The ability to deliver payloads with pinpoint accuracy makes it a formidable weapon on the battlefield.

Another key characteristic of the F111 Series 3 is its advanced cockpit design. The aircraft features a tandem two-seat configuration, which allows for seamless communication and coordination between the pilot and weapons systems officer. The cockpit is equipped with modern displays and controls that improve situational awareness and streamline operations.

In terms of durability, the F111 Series 3 is engineered to withstand harsh combat conditions. Its robust airframe is constructed to endure the stresses of high-speed flight and combat maneuvers, ensuring mission success even in challenging environments. Additionally, the aircraft's engines are designed for performance reliability, providing ample thrust while maintaining fuel efficiency.

Overall, the Honeywell F111 Series 3 stands out as a versatile and formidable platform in military aviation. With its advanced features, technologies, and characteristics, it continues to play a significant role in modern air operations, embodying the innovation and capabilities expected from contemporary military aircraft.
Top Page Image Contents