Horizon Fitness CST3.5-4.5, CST4.5 manual S E M B Ly, Unpacking, Tools Included, Parts Included

INTRODUCTION IMPORTANT PRECAUTIONS

A S S E M B LY

IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!

WARNING

During the assembly process of a the treadmill there are several areas that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly

READING RACK	CONSOLE
WATER BOTTLE HOLDER	TOUCH PAD PANEL WITH BLUE BACK-LIT DISPLAY

GRIP PULSE HANDRAILS
	SAFETY KEY PLACEMENT
ON/OFF SWITCH	CONSOLE MAST
CIRCUIT BREAKER	MOTOR COVER
	FOOT LOCK LATCH
POWER CORD

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. There should be no side-to-side play in the console masts or any forward and back play in the console assembly or handlebars. If there is any play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled

TRANSPORT WHEEL

SIDE RAIL

VS3™ Cushioning

CST4.5 SHOWN

RUNNING BELT / RUNNING DECK

SIDE RAIL

ROLLER END CAP

REAR ROLLER ADJUSTMENT CAPS

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL OPERATION

and in the upright folded position, with the lock latch secure. NOTE: The console assembly is located under the treadmill deck and should ONLY be removed after STEP 1 of the assembly instructions have been fully completed! FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY! Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

Before proceeding, find your treadmill’s serial number and model name located to the left of the on/off

TOOLS INCLUDED

5 mm Allen Wrench/Phillips Screw Driver

8 mm Allen Wrench or 6 mm Allen Wrench

PARTS INCLUDED

1 Safety Key

1 Console Assembly (located under treadmill deck)

1 Power Cord

1 Hardware Pack

2 Support Bars/Caps

2 Handlebars

TREADMILL OPERATION

CONDITIONING TROUBLESHOOTING LIMITED

GUIDELINES & MAINTENANCE WARRANTY

6

power switch and power cord and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND

MODEL NAME IN THE BOXES BELOW:

SERIAL NUMBER:

MODEL NAME:

*Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

*Also enter this serial number on your Warranty Card.

HARDWARE PACK CONTENTS (parts shown at actual size)

Teflon Washer (B)		Lock Washer (D)
Qty: 4		Qty: 2
top view
		Arc Washer (E)
45 mm Bolt (A)	8 mm Bolt (C)	Qty: 2
Qty: 2	Qty: 4

top view angle view

If you have questions or if there are any missing parts, we will guarantee complete satisfaction. Customer Tech Support contact information is located on the back panel of this manual.

7

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES

CST3.5-4.5 Treadmill Rev0.2.indd 6-7 4/21/05 11:22:33 AM