Switch Overview

Switch Hardware Features

Switch Overview

Switch Hardware Features

The ProCurve Series 2510-24 Switch (Switch 2510-24 (J9019A)) is a store and forward, multiport switch offering low latency for high-speed networking.

Switch Ports

ProCurve Switch 2510-24 (J9019A)

 

Power, Fault

 

 

Test Status LED

 

 

Link and Mode LEDs

 

 

and Locator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LEDs

 

 

 

 

 

 

 

 

 

 

 

 

 

ProCurve Switch

*

off = 10 Mbps,

 

flash = 100 Mbps,

on = 1000 Mbps

 

10/100Base-T Ports (1 - 24) — Ports are HP Auto MDI-X

Link

25T Mode

26T

 

 

2510-24

 

Mode

3

5

7

9

11

Link 13 Mode

15 17

19 21

23

 

 

 

 

J9019A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power

 

 

 

 

 

 

 

 

 

 

 

 

 

Dual-Personality Ports:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10/100/1000-T (T)

Fault

 

 

 

 

 

 

 

 

 

 

 

Link

Mode

 

or Mini-GBIC (M)

Locator

LED

Act

 

 

 

 

 

 

 

 

 

25M

 

26M

Use only one (T or M)

 

Mode

FDx

 

 

 

 

 

 

 

 

 

 

 

!

for each Port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Test

* Spd

 

 

 

 

 

 

 

 

 

 

 

 

 

Console

Reset

Clear

2 Mode

4

6

8

10

12

Link 14 Mode

16

22

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED Mode select button

 

 

 

 

Dual-personality ports

Console port

 

 

and indicator LEDs

10/100Base-TX

 

(10/100/1000Base-T* or

 

 

 

 

 

 

 

 

 

 

 

RJ-45 ports*

 

 

mini-GBIC)

Resetand Clear

buttons

* 10/100/1000Base-T ports have the IEEE Auto MDI/MDI-X feature.

The Switch 2510-24 has 24 auto-sensing 10/100Base-TX RJ-45 ports, and two dual-personality ports—either auto-sensing 10/100/1000Base-T RJ-45 or mini- GBIC.

The dual-personality ports have either auto-sensing 10/100/1000Base-T RJ-45, or mini-GBIC connectivity. Dual personality ports use either the 10/100/ 1000Base-T RJ-45 connector, or a supported ProCurve mini-GBIC for fiber- optic connection. If any of the mini-GBIC ports are used the corresponding RJ-45 port will be disabled. By default, the RJ-45 ports are enabled.

The Series 2510 Switch uses the console port to connect to a PC or workstation running a VT-100 terminal emulator, or VT-100 terminal. A cable to connect the console to the switch is supplied.

The Series 2510 Switch does not have a power switch; it is powered on when connected to an active AC power source. This switch automatically adjusts to any voltage between 100-127 and 200-240 volts and either 50 or 60 Hz. No voltage range settings are required.

1