Manuals / HP / Computer Equipment / Projector

HP mp3135w manual To install on a table, Installing Permanently

Models: mp3135w

1 84

Download 84 pages 4.53 Kb

Page 54

Installing Permanently

Installing Permanently

3.Attach the tripod mounting block to the tripod mount hole on the bottom of the projector.

4.Attach the projector and tripod mounting block to the tripod according to the tripod manufacturer’s instructions.

To install on a table

This installation is covered in detail in Chapter 1. See “Setting Up the Projector” on page 16 for more information.

54	User’s Guide

Image 54

HP mp3135w manual To install on a table, Installing Permanently

Contents

hp mp3130 digital projector user’s guide First Edition August Contents 1 Setting Up2 Giving Presentations 4 Maintaining the Projector 3 Adjusting the Projector5 Installing Permanently ContentsIndex 6 Fixing Problems7 Reference Specifications Safety Information Safety precautions Laser safetyContents User’s Guide“Setting Up the Projector” on page “Turning On and Off” on page Setting Up“What’s in the Box?” on page “Identifying Common Features” on page “Making Basic Adjustments” on pageWhat’s in the Box? Identifying the contents of the boxSymbol FunctionIdentifying Common Features Symbol Projector at a glanceIdentifying the projector FunctionSymbol Projector buttons and lightsIdentifying buttons and lights on the projector FunctionSymbol Back panelIdentifying the back panel FunctionSymbol Remote controlIdentifying the remote control with case closed FunctionIdentifying remote control with case open SymbolFunction Setting Up AccessoriesCeiling mount Projector screen Power cables Replacement lamp module Video cables“To position projector” on page “To set up on a table” on page Setting Up the ProjectorThis section describes how to set up, plan, and connect the projector “To connect power” on page “To connect a computer” on pageImage size diagonal To position projectorIdentifying image size relative to distance from screen Image size widthwidth of screen = 0.8 × diagonal of screen for 43 screen Calculating projection dimensionsSetting Up A = 1.67 to B = 1.2 to 12 m 4 to 40 ft C = 0.21 toTo set up on a table To connect powerTo connect a computer Computer with VGA portComputer with DVI port Setting UpUser’s Guide To connect a handheld organizer To connect video sources S-video connectionComposite video connection Setting UpComponent video connection Setting UpUser’s Guide SCART connection Turning On and Off To turn the projector onTo reset the projector To turn the projector offMaking Basic Adjustments To aim the projectorTo adjust the focus and zoom Using the Remote Control Giving PresentationsSlide the remote control case open to use additional buttons Showing Presentations To present from a computerTo change the source To hide or show the displayAdjusting the Projector Adjusting the Picture and SoundTo adjust the shape of the picture To adjust the image according to the type of picture To adjust other image settings To adjust the audioTo adjust the projector setup Using the On-Screen Menu To change settings using the on-screen menu Quick choice menu Quick choiceInput menu InputAdjust picture menu Adjust pictureAdjust picture continued Best FitAudio menu Setup menuSetup AudioAdjusting the Projector Help menuHelp User’s GuideAdjusting the Projector User’s GuideMaintaining the Projector Performing Routine MaintenanceTo clean the projector lens To get the projector status4. Slide the new lamp housing onto the projector To replace the lamp module3. Slide the lamp housing off the projector 1. Turn off the projector and allow it to cool for 30 minutes7. Open the on-screen menu and select Setup Reset lamp hours Maintaining the ProjectorUser’s Guide To replace the battery in the remote control To update the firmware Upgrading the ProjectorUSB method Maintaining the Projector User’s GuideInstalling Permanently Installing the ProjectorTo mount the projector on a tripod To install on a table Installing PermanentlyTo install on the ceiling To install for rear projection To lock the projector Installing Permanently User’s GuideFixing Problems Troubleshooting SuggestionsStart-up problems If no lights or sounds turn onIf nothing is projected but the projector seems to start up Picture problems If the wrong input source is displayedIf the image is too small or too large If the image is out of focusIf an upside-down or reversed image is displayed If the image has slanted edgesIf the image is stretched If a scrolling or cut-off image is displayedIf the image is flickering or unstable If the image disappears from the computer screenIf the projected colors seem completely wrong If the picture settings are completely wrong and you cannot fix themIf a DVI device causes an error message or garbage on the screen If the projector stops responding to all controlsIf the lamp indicator or temperature indicator turns on or blinks Sound problemsInterruption problems If no sound is coming out of the projectorIf the lamp shuts off during a presentation Remote control problemsIf the remote control does not operate If the lamp burns out or makes a popping soundFixing Problems Testing the ProjectorTo run the projector diagnostics User’s GuideFixing Problems User’s GuideSpecifications Identifying the projector specificationsReference Identifying the projector specifications continued ReferenceTemperature -20 to 55C -4 to 131F Humidity 80% RH max, non-condensing Identifying the projector specifications continuedEnvironmentOperating Temperature 10 to 35C 50 to 95F Noise levelV-Sync Hz Analog Video Mode CompatibilityCompatibility H-Sync kHzV-Sync Hz Analog Video Mode Compatibility continuedCompatibility H-Sync kHzDigital Video Mode Compatibility CompatibilityH-Sync kHz Safety Information Safety precautionsLaser safety LED safety Mercury safetyRegulatory Information U.S.ACanada Japan Korea ReferenceUser’s Guide Reference InternationalConforms to the following product specifications User’s GuideReference User’s GuideIndex Page Page Index IndexUser’s Guide