Hubbell CLT2054, CLT1554 manual Description, Specifications, Precautions, Installation

H-MOSS®Motion Switching System

Passive Infrared / Ultrasonic Occupancy Sensors

Installation and Operating Instructions

DESCRIPTION

The H-MOSS® sensor is an intelligent self-adapting occupancy sensor that is designed to replace existing wall switches.

SPECIFICATIONS

•1000 sq. ft coverage area (Models: AP1277 and AD1277)

•400 sq. ft. coverage area (Models: AU1277)

•Single or Dual circuit 120/277VAC, 50/60Hz operation

•Electrical Ratings: (Each Output Separately) 120VAC – 800W Incandescent, 1000W Ballast, 1/6 HP 277VAC – 1800W Ballast, 1/6 HP

•Adjustable Time Delay: 4-30 minutes, self-adapts based on occupancy

•Light Level Adjustment (Circuit B output on Dual Circuit versions): 10-500+FC

•UL Listed

PRECAUTIONS

CAUTION: RISK OF ELECTRICAL SHOCK. Turn power off at service panel before beginning installation. Never wire energized electrical components.

Read and understand all instructions before beginning installation. NOTICE: For installation by a licensed electrician in accordance with National and/or local Electrical Codes and the following instructions. NOTICE: For indoor use only.

CAUTION: USE COPPER CONDUCTOR ONLY.

Confi rm that device ratings are suitable for the application prior to installation.

NOTICE: Do not install if any damage to product is noticed.

INSTALLATION

1.Turn power off at the service panel.

2.Remove the old switch(es) if applicable.

3.Wire as shown in the Wiring Diagram section. A secure connection to ground is necessary for the sensor to function properly.

4.Install sensor in wall box using mounting screws provided.

5.Restore power to the sensor and allow it to self adjust (up to 2min.).

6.Remove the sensor’s cover – see Adjustments section.

7.If desired, calibrate the photocell sensor and adjust the sensor’s confi guration switch settings as described below.

8.Reinstall the sensor’s cover.

9.Install a Style Line® wall plate (not included).

Test Mode – to enter test mode:

1.Make sure lights are on.

2.Press and hold the ON/OFF button until the lights cycle off then back on. For dual circuit sensors, press and hold the ON/OFF button for Circuit A. For No-button sensors, press and hold the Test Button. See Sensor Operation Diagram.

3.Sensor is now in test mode. Vacate room, lights should turn off after 5 seconds. Step back into room (sensing zone), lights will turn back on. Repeat as necessary to confirm sensor is operating and detecting in the lighting zone as desired. Sensor will flash red or green LED to indicate Passive Infrared or Ultrasonic occupancy detection as applicable.

4.To exit Test Mode, press any button. Note: Sensor will automatically exit Test Mode after 1 hour.

Manual Override – Press button(s) to toggle lights ON and OFF. Lights will remain in the last state determined by the buttons while occupancy is detected. Sensor will return to automatic mode when the sensor’s unoccupied timer value is reached. Note: No-button sensors cannot be manually turned off.

Wiring Diagram		Range Diagram
120/277VAC	Red
Black	Load 1
	50 '
Green
Ground
		26 '
	15 '
		16 '
		29 '
Single Circuit		56 '
	US	Major motion
	US	Minor motion
	PIR	Major Motion

Line circuit 1 120/277 VAC

Black	Red		Black	Red
		Load1			Load1
Green			Green
Ground	Line circuit		Ground
	120/277 VAC
Blue	Violet		Blue	Violet
		Load 2			Load 2
Line circuit 2
120/277 VAC

Dual Circuit Sensor	Dual Circuit Sensor
(Wired for Dual Circuits)	(Wired for Single Circuit)

Sensor Operation Diagram

Photocell		Photocell
Push-Button
		Push-Button
Confi guration		Confi g-	Button A
	Button A	uration
Switches			(Test Button)
	(Test Button) Switches
	Air Gap Switch		Air Gap Switch
			Button B
Cover Release	Cover Release
Catch		Catch

One/No Button Sensor Two Button Sensor

Wiring Device-Kellems			®
Hubbell Incorporated (Delaware)
185 Plains Road
Milford, CT 06461-2420
(203) 882-4800
PD2218	Page 1	04/09	PRINTED IN USA