Continuous

 

 

Do

 

 

 

 

 

over-temperature

 

contactors pull out

 

 

 

 

 

 

 

 

condition

 

at setpoint?

 

 

 

 

 

 

 

 

 

Yes

 

 

 

 

 

 

 

Yes

 

Is there

 

 

 

 

 

 

 

 

 

 

 

zero amp draw when the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

contactors drop out at

 

 

 

 

 

 

 

 

 

 

 

 

 

setpoint?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No

 

 

 

 

 

 

 

 

 

Correct

temperature

setpoint?

No

Properly set temperature

 

 

 

Are configuration

 

 

 

settings set properly,

Yes

 

 

 

 

per Section III, Para.

 

 

 

 

 

 

4?

 

 

 

 

 

 

 

 

 

 

Yes

Diagram 3

 

 

 

White

1

 

 

Black

2

 

Is there

Red

3

 

208/240V across

 

 

Yellow

4

terminals of J5 on the

 

 

control board as shown

 

J5

 

in the

 

diagram 3?

For 1 contactor:

 

 

 

 

check voltage across 1 & 4

 

 

For 2 contactor:

 

 

Yes

check voltage across 1 & 3 and 1 & 4

 

No

No Replace contactor

setpoint

Contact factory

Plug probe end into RJ45 pigtail

(not supplied). Check ohms

across terminals 1and 4

(see diagrams 1 & 2). Compare this with the ohms the thermistor

should supply for the actual

temperature in the tank

Do ohms match?

No

Replace probe

 

 

 

Replace control

Yes

 

 

 

board

 

 

 

 

 

 

 

 

 

 

 

 

 

OK?

No

Any or all buttons do not work, but display is operational.

 

Re-seat ribbon

 

 

 

 

 

 

cable from display

 

 

 

OK?

 

 

 

 

 

to control board

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Verify that the

 

 

 

 

 

 

display is properly

 

 

 

 

 

Individual display

 

 

Re-seat ribbon

 

 

elements do not

 

 

cable from display

 

 

work or unusual

 

 

to control board. Be

 

OK?

 

 

 

characters are

 

 

sure ribon cable is

 

 

displayed

 

 

not reversed.

 

 

No

seated to the base

 

 

 

 

OK?

and that the

 

 

 

 

 

 

 

 

buttons click when

 

 

 

 

 

pressed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace digital

display

OK?

No

Replace digital

display

Replace control

board

OK?

No

Replace control

board

24

Page 24
Image 24
Hubbell Electric Heater Company J manual Continuous