Hughes & Kettner DSM manual Technical Specifications, Appendix

ZENTERA - MANUAL

E2) The zenTera® is cabled up and connected properly, but no sound is audible.

•One or more of the volume knobs or the master knob is/are turned all the way down. Dial in higher settings.

•The internal speakers are not connected. Plug them in.

•The zenTera® is in TUNER mode, which means that it is muted. Quit TUNER mode by tapping the rTUNER button.

•A shorted external speaker cable caused one of the internal fuses to blow. Have a qualified technician change the fuse (ensure the replacement fuse bears the proper rating).

•The volume pedal of the connected Z-Board is set to the minimum position. Floor the pedal.

E3) The zenTera® will not respond to the Z-Board or footswitch.

•The connector of the Z-Board or footswitch is not plugged in correctly or at all. Plug it into the zenTera®, ensuring that it is seated firmly.

E4) The sound is totally distorted when you activate a connected effects device.

•The input of the effect device is being overdriven. If it is equipped with a level meter or other level indicator, check the signal level and back off the signal processor's input sensitivity (via a knob labeled "Input" or "Gain").

E5) The signal level drops considerably when you connect an external effects device,

•The effect device is sending the signal back at too low a level. Turn up the signal processor's output level.

E6) A connected MIDI controller is not getting operating voltage via the phantom power feed of the MIDI IN port:

•The MIDI cable is defective. Replace it with a new cable.

•The phantom power fuse tripped. Replace the blown fuse making sure that the replacement has the same specs as the original fuse.

10.0 TECHNICAL SPECIFICATIONS

PREAMP SECTION

INPUT	-10 dBV / 1 M ohm
FX RETURN L/R	0 dBV / 10 K ohms
FX SEND L/R	0 dBV / 220 ohms
RECORDING OUT L/R	0 dBV / 220 ohms

POWER AMP SECTION

OUTPUT POWER	2 x 100 watts into 6 ohms
FREQUENCY RESPONSE	2 x 60 watts into 16 ohms
	20 Hz - 20 KHz
SPEAKER OUTS	Minimum impedance per channel:
LOUDSPEAKER	6 ohms (1 x 16 ohms + 1 x 8 ohms)
	Celestion Vintage 30, 16 ohms
HEADPHONES OUT	500 mW into 4 - 600 ohms

11.0APPENDIX

11.1TABLE: EFFECTS AND EFFECT PARAMETERS

The following overview gives you a survey of all of the zenTera®'s effects and effect parameters. Note that you must first activate the appropriate effect menu before you can enter and edit settings. Activate INS FX by tapping the rAMP TYPE knob and the remaining menus by turning or tapping WrMOD FX, DELAY and/or REVERB.

INS FX

TYPE	PARA 1		PARA 2
Wah Wah	-	-	-	-
Wah Wah 2	-	-	-	-
Fix Wah	Frequency	0.23 - 1.55	-	-
Fix Wah 2	Frequency	0.50 - 2.21	-	-
Mod Wah	Rate	0.0 - 10.0	Intensity	0 - 100
Mod Wah 2	Rate	0.0 - 10.0	Intensity	0 - 100
Comp Short	Make Up Gain	0.0 - 15.0	Intensity	0 - 100
Comp Medium	Make Up Gain	0.0 - 15.0	Intensity	0 - 100
Comp Long	Make Up Gain	0.0 - 15.0	Intensity	0 - 100
Tube Scream	Gain	0.0 - 10.0	Level	0.0 - 10.0
Fuzz	Gain	0.0 - 10.0	Level	0.0 - 10.0

MOD FX

TYPE	PARA 1		PARA 2
Chorus Mono	Rate	0.1 - 10.0	Depth	0 - 100
Chorus Stereo	Rate	0.1 - 10.0	Depth	0 - 100
Flanger 1 Mono	Rate	0.1 - 10.0	Intensity	0 - 100
Flanger 1 Stereo	Rate	0.1 - 10.0	Intensity	0 - 100
Flanger 2 Mono	Rate	0.0 - 10.0	Intensity	0 - 100
Flanger 2 Stereo	Rate	0.0 - 10.0	Intensity	0 - 100
Phaser	Rate	0.1 - 10.0	Colour	0 - 100
Phaser XL	Rate	0.1 - 10.0	Colour	0 - 100
Tremolo	Rate	0.5 - 10.0	Shape	0 - 100

DELAY

TYPE	PARA 1		PARA 2
Echo	Time	10 ms - 2 s	Feedback	0 - 100
Ping Pong	Time	10 ms - 2 s	Feedback	0 - 100
Tape Echo	Time	10 ms - 2 s	Feedback	0 - 100
Tape Hallo	Time	10 ms - 2 s	Feedback	0 - 100
Tape Multi	Time	10 ms - 2 s	Feedback	0 - 100
Hold Echo	>>PLEASE USE TAP BUTTON<<		Feedback	0 - 100
Hold Ping Pong	>>PLEASE USE TAP BUTTON<<		Feedback	0 - 100
Hold Tape	>>PLEASE USE TAP BUTTON<<		Feedback	0 - 100

ENGLISH

General Specifications

MAINS VOLTAGE	230 volts AC (European version)
	117 volts AC (North American version)
MAX. POWER CONSUMP.	100 volts AC (Japanese version)
	708 VA
MAINS FUSE	T 2.5 A (230 V model)
	T 5 A (117 V model)
EXTERNAL FUSES	T 6.3 A (100 V model)
	T 500 mA MIDI Phantom
INTERNAL FUSES	2 x T 5 A (power amp)
	1 x T 2.5 A (DSP)
DIMENSIONS (W X H X D)	2 x T 500 mA (analog section)
	750 x 585 x 300 mm
WEIGHT	30 kg

REVERB

TYPE	PARA 1		PARA 2
Hall	Time	0.0 - 15.0	Predelay	0 - 100
Spring	Time	0.0 - 15.0	Predelay	0 - 100
Garage	Time	0.00 - 5.00	Predelay	0 - 100
Stage	Time	0.0 - 15.0	Predelay	0 - 100
Small	Time	0.00 - 5.00	Predelay	0 - 100
Bright	Time	0.0 - 15.0	Predelay	0 - 100
Normal	Time	0.0 - 15.0	Predelay	0 - 100
Warm	Time	0.0 - 15.0	Predelay	0 - 100

15