531617-1_A - 1197c_ManE.qxp 11/6/2007 4:36 AM Page 22

To route the transom transducer cable:

The transducer cable has a low profile connector that must be routed to the point where the control head is mounted. There are several ways to route the transducer cable to the area where the control head will be installed. The most common procedure routes the cable through the transom into the boat.

NOTE: Your boat may have a pre-existing wiring channel or conduit that you can use for the transducer cable.

1.Unplug the other end of the transducer cable from the control head. Make sure that the cable is long enough to accommodate the planned route by running the cable over the transom.

CAUTION! Do not cut or shorten the transducer cable, and try not to damage the cable insulation. Route the cable as far as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference. If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50' (15 m). For assistance, contact the Customer Resource Center at www.humminbird.com or call 1-800-633-1468 for more information.

NOTE: Since the transducer may need to pivot up to 90° in the bracket if it strikes an object, make sure there is sufficient cable slack to accommodate this motion. It is best to route the cable to the side of the transducer so the cable will not be damaged by the rotation of the transducer.

2.If you will be routing the cable through a hole in the transom, drill a 5/8" diameter (16 mm) hole above the waterline. Route the cable through this hole, then fill the hole with marine-grade silicone sealant and proceed to the next step immediately.

Routing the Cable

3. Place the escutcheon plate over the cable hole and use it as a guide to mark the two escutcheon plate mounting holes. Remove the plate, drill two 9/64" (3.5 mm) holes, then fill both holes with marine-grade silicone sealant. Place the escutcheon plate over the cable hole and attach with two #8 x 5/8" (16 mm) wood screws.

4. Route and secure the cable by attaching the cable clamp to the transom; drill one 9/64" dia. (3.5 mm) x 5/8" deep (16 mm) hole, then fill hole with marine-grade silicone sealant, then attach the cable clamp using a #8 x 5/8" (16 mm) screw.

5. Plug the other end of the transducer cable back into the control head connection holder.

Storing Excess Cable

NOTE: If there is excess cable that needs to be gathered at one location (as shown in the illustration), dress the cable routed from both directions so that a single loop is left extending from the storage location. Doubling the cable up from this point, form the cable into a coil. Storing excess cable using this method can reduce electronic interference.

22

Page 29 Page 31
Page 30
Image 30
Humminbird 1197C SI warranty To route the transom transducer cable
Page 29 Page 31

1197C SI specifications

The Humminbird 1197C SI is a high-performance fishfinder that has made waves in the world of angling technology. This device seamlessly integrates cutting-edge sonar technology with an intuitive user interface, making it a favorite among both novice and professional anglers.

One of the standout features of the 1197C SI is its Side Imaging technology. This unique sonar function allows users to see what lies beneath the water's surface, providing a wide, detailed view of the underwater environment. It operates at a frequency of 455 kHz and 800 kHz, enabling exceptional clarity and detail, even at considerable depths. This feature is particularly beneficial for identifying underwater structures such as rocks, wrecks, and weed beds, which are often hotspots for fish.

Another innovative component of the 1197C SI is its DualBeam PLUS sonar. This technology provides both a narrow and a wide beam, giving users the versatility to search for fish over a broader area while also honing in on specific targets. The combination of Side Imaging and DualBeam sonar results in an impressive level of detail and accuracy in fish detection.

The 1197C SI also boasts a large 10.4-inch color display, providing crisp visuals and easy navigation through the various features. The screen is designed for easy reading in bright sunlight, ensuring that anglers can rely on it no matter the fishing conditions. Additionally, the unit supports a variety of view options, allowing users to select from different display modes to suit their preferences.

Integration with GPS is another key characteristic of the Humminbird 1197C SI. Built-in GPS capabilities allow anglers to mark waypoints, create routes, and access detailed maps and charts. This feature not only aids in navigation but also helps anglers return to successful fishing spots with ease.

The 1197C SI is also equipped with advanced networking capabilities, enabling it to connect with other devices, such as additional sonar units or autopilot systems. This increases the overall functionality and enhances the fishing experience by providing a more integrated system.

In conclusion, the Humminbird 1197C SI stands out for its advanced technologies such as Side Imaging, DualBeam sonar, and comprehensive GPS capabilities. With its large display and user-friendly interface, it has become an essential tool for anglers looking to increase their success on the water. With lasting durability and a wealth of features, the 1197C SI is a smart investment for serious fishing enthusiasts.
Top Page Image Contents