Humminbird 967C specification

3.The GPS receiver has two wire routing notches. Use the cable notch closest to the intended cable route.

4.With the cable routed, position the GPS receiver in the planned mounting location and mark the mounting holes with a pencil or punch.

5.Move the GPS receiver to the side and drill the two 9/64" (3.5 mm) pilot holes.

6.Align the GPS receiver's screw holes over the pilot screw holes and attach with the #8 - 1 1/4" Phillips head screws. Hand tighten only!

Finish Routing the Cable and

Check GPS Receiver Operation

After installing a GPS receiver, you should perform the following procedure to finish routing the GPS cable to the control head and to check to make sure that the control head is working correctly.

1.Secure the cable along its path to the control head as needed with cable ties.

2.Plug the GPS receiver cable into the Communications port on the control head. See Testing the System Installation to use the System Status start-up option and/or the GPS Diagnostic View to confirm a good installation.

1 2 3 4

1 Power

2Temp/Speed

5

3Communications

4Transducer

5Cable Collector Insert

24

Image 32

Humminbird 967C manual Finish Routing the Cable Check GPS Receiver Operation

Contents

Page Thank You Humminbird, Eufaula AL, USA. All rights reserved Table of Contents Views Iii Upper Range Start RecordingStop Recording Delete Image Sonar Menu Tab Export All Nav Data Delete All Nav Data101 102 Vii Series Introduction How the 900 Series Works 2D Sonar Peak to Peak measures power output at the highest points3D Sonar How GPS and Cartography Work Software Updates Accessory Bus Multi-Media Card MMC/SD Slot Accessory Bus Installation Overview900 Series has a wide variety of configurations Gimbal Mounting the Control Head Control Head InstallationBasic installation tasks that you must perform include Page Mounting Screws Cables Routed Directly Beneath Mounting Bracket Cables Routed Behind Mounting Bracket Plug Cable Connector Assembly to Connecting the Control Head Power Cable to the Boat Transducer Installation Transom Transducer Installation Determine transducer mounting location Mount the transducer bracket to the boat Attach the pivot to the transducer Attaching the Bracket Mount the transducer pivot assembly to the bracket Adjust the running position of the transducerInstallation after high speed testing Normal Cavitation Route the transom transducer cable Tighten the Pivot Screws Inside the Hull Transducer Installation Perform a final test of the transom transducer installationRouting the Cable Preferred Mounting Area Trial installation Determine the transducer mounting location Route the cable Permanently mount the transducer Trolling Motor Transducer Installation Test and Finish the Transducer InstallationTrolling Motor Transducer Options Are included with the bracket GPS Receiver Installation If you have… Then use Abrasion Stem Mounting with an Existing 1 14 Thread StemFollow these steps to stem mount the GPS receiver Access Under Mounting Location No Access Under Mounting Location Finish Routing the Cable Check GPS Receiver Operation Routing the cable to the control head Temperature Probe Accessory InstallationInstall the temperature probe accessory Testing the System Installation To test the installation Getting Started Using Your 900 Series Powering Up the Control Head Timer Elapsed time with Speed input or GPS Receiver What’s On the 3D Sonar Display What’s On the 2D Sonar Display RTS Real Time Sonar Window Real Time Sonar RTS Window Bottom Presentation POWER/LIGHT Key Key Functions View Key Menu Key Exit Key View Preset keysWAY Cursor Control Key Info Key Mark KeyGoto Key Goto Key has multiple functions, depending on the situation Views and Readouts Zoom +/- KeysViews 3D/2D Combo View 2D Sonar View 2D Sonar View 2D Zoom View 2D Zoom View Beam Sonar View Snapshot and Recording View Snapshot and Recording ViewPage Recording Slider Bar Recording Playback Bird’s Eye View Bird’s Eye View Chart/Bird’s Eye Combo View Chart/Chart Combo View Chart/Chart Combo View Chart View Chart/3D Combo View Chart/3D Combo View Chart/2D Combo View Chart Orientation Viewing Cartography Navigation Waypoints, Routes and Tracks Waypoints, Routes and Tracks Save, Edit, or Delete a Waypoint Navigate to a Waypoint or Position Add a Waypoint Target or Trolling Grid Chart View with Grid Save, Edit or Delete a Route Save or Clear a Current Track Edit, Delete or Hide Saved Tracks Man Overboard MOB Navigation Menu System Start-Up Options Menu Normal Simulator System Status Exit Normal operation by powering your 900 Series off Normal OperationSimulator System Status Self Test Accessory TestAccessory Test Screen GPS Diagnostic View 2D Sonar Views only 2D Sonar X-Press MenuActive Side Split Position Sensitivity Upper Range Lower Range Chart Speed 2D Zoom View only, when Bottom Lock is OnBottom Lock Bottom Range 2D/3D Priority Cancel NavigationOnly when Navigating 3D Sonar X-Press Menu 3D Sonar Views only Beam Sensitivity 3D Bottom Zoom3D Lower Range Beam Sonar View only Reset 3D View 3D History Navigation X-Press Menu Left Cursor key Waypoint Name Only with an active cursor on a waypoint Chart or Combo view only Cursor to WaypointSave Current Track Clear Current Track Skip Next Waypoint Cancel MOB NavigationSave Current Route Remove Target Remove GridOnly if a Target is active Only if a Grid is active Snapshot and Recording PressMenu Snapshot and Recording Press MenuSnapshot and Recording View only Delete Image Start RecordingStop Recording Delete All Images Delete Recording To specify the pings per second Delete All RecordingsPings Per Second To specify playback speed Playback SpeedStop Playback Sonar Menu Tab 2D Sonar Colors3D Bottom Style Sonar Menu Fish ID+ 3D Frame Style2D Beam Select Fish ID Sensitivity Fish ID 3D Reference RTS Window Narrow RTS Window Off Bottom ViewZoom Width KHz Sensitivity Depth LinesAdvanced Depth Lines Surface Clutter Noise Filter Water Type To change the Max Depth settingMax Depth Temperature Graph 2D Sonar View only, with Temperature inputColor Bar Navigation Menu Tab Current Track Saved TracksCurrent Track Submenu Saved Tracks Submenu Waypoints RoutesWaypoints Submenu contains the following menu choices Waypoints Submenu North Reference Trolling Grid Rotation Trackpoint Interval Track Min Distance Track Color Range Map DatumCourse Projection Line Export All Nav Data Continuous Navigation Mode Chart Menu TabContinuous Navigation Mode allows you to Delete All Nav Data Chart Detail Level Map Borders Lat/Lon Grid Spot SoundingsNavaids on Birds Eye View Shaded Depth Set Simulation Position Set Map Offset Alarms Menu Tab Clear Map Offset Low Battery Alarm Depth AlarmFish ID Alarm Aux Temp Alarm Temp AlarmWith optional-purchase temp. probe or Temp/Speed only 100 Off Course Alarm Off Course AlarmArrival Alarm Drift Alarm Circle Drift AlarmAlarm Tone Setup Menu Tab Setup MenuUnits Depth Units Temp User Mode Units DistanceUnits Speed Language Triplog Reset Restore DefaultsOff Triplog Position Voltage Aux. Temperature Select ReadoutsPage Temp. Offset Depth OffsetAux. Temp. Offset Speed Calibration Local Time ZoneDaylight Saving Time Position Format Time Format Date FormatDigits Format Advanced, International only 110 Nmea OutputSonar Views Menu Tab Accessories Menu Tab Using Screen SnapshotPage 114 TroubleshootingSeries Doesn’t Power Up 115 Display ProblemsControl head loses power at high speeds Finding the Cause of Noise Year Limited Warranty 117 118 Humminbird Service PolicyReturning Your Unit for Service Series Accessories Series includePage 121 SpecificationsArea of Coverage kHz 74 @ -10 dB 455 kHz 53 @ -10 dB Glossary 122 123 Glossary Receiver See Transmitter 125 Glossary Glossary Sonar Terms 127 Glossary 129 Glossary Glossary Appendix A, Transducer Mounting Template SHS 7W 133 134 Contact Humminbird 135