Temperature Graph, Navigation Menu TAB | Humminbird 981 instruction

98x_Manual_531376-1_A.qxd 2/23/2005 11:40 AM Page 71

TEMPERATURE GRAPH

(Sonar View only, with Temperature input)

Temperature Graph allows you to display or suppress a water temperature graph over the main Sonar View to show temperature changes correlated to recent sonar history.

To change the display of the Temperature Graph:

1.In the Sonar View, highlight Temperature Graph on the Sonar main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the display of the water temperature graph. (Off, On, Default = Off)

NAVIGATION MENU TAB

(987c SI Combo Models only)

Press the MENU key twice to access the Main Menu System, then press the RIGHT cursor key to select the Navigation tab.

NOTE: Menu choices will vary depending on system settings.

98xManual531376-1A.qxd 2/23/2005 1139 AM Thank You Table of Contents Sonar Menu Tab Menu System Start-Up Options MenuSonar X-Press Menu Side Imaging X-Press Menu Setup Menu Tab Alarms Menu Tab Contact Humminbird Views Menu Tab Accessories Menu Tab Troubleshooting Dualbeam Plus Sonar Series IntroductionHOW the 900 Series Works Side Imaging Sonar Multi-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD Slot Accessory Bus Accessory BUSInstallation Overview 900 Series has a wide variety of configurations Control Head Installation Gimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Speed Communications Transducer Cable Collector Insert Cables Routed Near Mounting Bracket In-dash mounting template IN-DASH Mounting the Control HeadParts and tools specific to In-dash mounting are In-dash mounting foam pads 23/2005 Beginning of this procedure Connecting the Control Head Power Cable to the Boat Motor Position Transducer InstallationTransom Transducer Trolling Motor Transducer Stepped Hull Transom Transducer Installation Not a hull, motor, or other transducer, etc Without deadrise adjustment Completely tighten Be fully tightened until all adjustments are madeHeaded pin can be inserted from either side of the bracket Normal Cavitation Force is necessary to pivot the assembly Trolling Motor Transducer Installation Hand-tighten only Test and Finish the Transducer Installation To the cable as shown Follow these steps to stem mount the GPS receiver Access Under Mounting Location Access Under Mounting LocationNo Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation Speed Accessory Installation Hand tighten only Install the Speed accessory Rotating Retaining Axial Clip to Remove Paddlewheel Testing the System Installation Getting Started Using Your 900 Series Powering UP the Control Head Triplog WHAT’S on the Sonar Display Sonar Bottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window KHz provides maximum coverage with 180 total beam width KHz provides highest resolution with 160 total beam widthUnderstanding Side Imaging Topography Changes Bottom Return Triplog WHAT’S on the Side Imaging Display Side Imaging Representation Side Imaging Technology HOW IT WorksSide Imaging on the Water Interpretation Submerged Ravine with Timber Submerged Swimming Pool Submerged Standing and Fallen Timber, Plus Bait Fish Menu KEY POWER/LIGHT KEYKEY Functions View KEY Info KEY View Preset KeysWAY Cursor Control KEY Exit KEY Sonar views ViewsMARK/GOTO KEY Views available on your 900 Series are Sonar View Views and ReadoutsSonar View Sonar Zoom View Sonar Zoom View Side Imaging View Split Sonar ViewSide Imaging View Split Sonar View Side/Sonar Combo View SIDE/SONAR Combo View Bird’s Eye View Chart/Bird’s Eye Combo View Chart/Sonar View Chart View with Active Cursor Chart/Side Combo View CHART/SIDE Combo View Navigation Chart View with Cursor Present Waypoints, Routes and Tracks WAYPOINTS, Routes and Tracks Navigate to a Waypoint or Position ADD a Waypoint Target or Trolling Grid Chart View with TargetChart View with Grid SAVE, Edit or Delete a Route Press Menu Menu System Start-Up Options Menu Sonar Tab, Normal Mode Sonar Tab, Advanced ModeSTART-UP Options Menu Normal Simulator System Status System Status Self Test Accessory Test GPS Diagnostic ViewNormal Operation Simulator GPS Diagnostic View Accessory TestAccessory Test Screen Split Position To Adjust Split Screen PositionSonar X-PRESS Menu Active Side Upper Range To adjust the SensitivityTo adjust the Upper Range Sensitivity Zoom Level Chart SpeedLower Range Sonar Colors Bottom LockBottom Range Side Imaging X-Press Menu Highlight Split Position on the Side Imaging X-Press MenuSide Imaging Views only SI Range SI SideSI Sensitivity Highlight SI Colors on the Side Imaging X-Pressmenu SI ColorsNavigation X-PRESS Menu To change the SI Colors To Clear Current Track Save Current TrackClear Current Track To Save Current Track Remove Target Cancel NavigationSave Current Route Skip Next Waypoint Only if a Grid is active Remove GridSonar Menu TAB To Remove a Grid Fish ID+ Beam SelectSide View Frequency Highlight Fish ID Sensitivity on the Sonar main menu To change the Fish ID Sensitivity settingFish ID Sensitivity To turn Fish ID+ on or off Zoom Width To change the RTS Window settingTo adjust the Bottom View Bottom View Noise Filter KHZ SensitivityDepth Lines Surface Clutter Color BAR MAX DepthWater Type Navigation Menu TAB Temperature GraphTo change the display of the Temperature Graph Sonar View only, with Temperature input Routes TracksWaypoints Trackpoint Interval Chart OrientationNorth Reference Trolling Grid Rotation Delete ALL NAV Data Track MIN DistanceMAP Datum Export ALL NAV Data MAP Borders Chart Menu TABChart Detail Level To change the Chart Detail Level setting SET Simulation Position LAT/LON GridSpot Soundings Shaded Depth Clear MAP Offset Alarms Menu TABTo change the Map Offset setting SET MAP Offset Temp Alarm Depth AlarmFish ID Alarm LOW Battery Alarm Drift Alarm OFF Course AlarmArrival Alarm Highlight Alarm Tone on the Alarms main menu Alarm ToneSetup Menu TAB To change the Alarm Tone setting Units Speed Units DepthUnits Temp Units Distance Language User ModeTriplog Reset Restore Defaults Select Readouts Default Sonar View Temp Offset To change the Depth Offset settingTo change the Temp Offset setting Depth Offset Position Format Speed CalibrationLocal Time Zone Daylight Saving Time Nmea Output Time FormatDate Format To Change the View Status of Any View Views Menu TABTo turn Sonar on or off Following views are available Series Defaults to Simulator with a Transducer Attached Accessories Menu TABTroubleshooting Series Doesn’t Power Up Control head loses power at high speeds Display Problems Boat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appears Humminbird Service Policy Year Limited Warranty For IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Area of Coverage Specifications Transducer Mounting Template XHS-9-SI-160-T Appendix a Contact Humminbird

Humminbird 981 Temperature Graph, Navigation Menu TAB, Sonar View only, with Temperature input

Models: 981

TEMPERATURE GRAPH

(Sonar View only, with Temperature input)

To change the display of the Temperature Graph:

NAVIGATION MENU TAB

(987c SI Combo Models only)

Navigation Menu